Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Hi DevZone,
I am currently working on an external Flash OTA update via SQSPI on the nRF54L15 DK (v0.7.0). I have already verified that SQSPI read/write operations are...
Hi, I'm using a WisBlock setup with: • RAK19001 base board • RAK4631 core RAK18030 microphone in IO slot A • RAK15002 microSD in IO slot B I'm running Zephyr / nRF Connect...
nRF54L15 DK Board
BM-SDK-V1.0
Hi：
I have debugged the IRQ according to the nrfx demo, but now there is an unresolvable error that requires assistance.
This is an error...
Hello Nordic-Team,
I am using the SENSING mechanism on GPIOs to wake up a firmware from SYSTEM OFF. Two GPIOs are used for this and it is crucial for the firmware to detect...
I'm using nRF Connect for Desktop on Linux and updated today to v5.3.0.
I have J-Link V9.24a installed and it is available in $PATH. Also it works well with Programmer v4...
Hello Nordic Team,
We are currently working with the nRF54LM20B device and would like to understand whether Bluetooth Channel Sounding is supported on this SoC.
Specifically...
Hi,
This is more of a bug-report than really a help question, as it can be dealt with.
The device I am developing uses an external flash for storing MCUBoot's slot-2,...
I have been working on a soil moisture sensor for my indoor plants and I wanted to build some skills in PCB design using a Nordic SoC. I have chosen the nrf54L15 for this...
Hello Nordic Team,
I am working on a project based on the following requirements, where I have added multiple configurations and peripherals in my firmware, and I need to...
Dear Nordic Team,
We are seeking assistance in resolving a significant power consumption gap observed in our nRF9151-based asset tracker. While our lab testing suggests...
Hello Nordic Team,
I am working on an application using the nRF52833 with the following requirements:
Device operates as both BLE Central + Peripheral
Stores bonding...
Hi,
I’m looking to program an external device that runs on 3.3V with my NRF52840 DK (v3.0.1), and I’m looking to verify that this is possible. I know that the DK runs at...
It seems there might be a small issue with the TF-M GPIO MCU-select IOCTL plumbing on nRF54L — specifically when a non-secure app tries to configure sQSPI GPIOs (and presumably...
Hello guys,
Im developing RTLS with DWM3001C and right now Im working on personal tag powered by CR2450. So naturally, power consumption should be as low as possible....
Hi，
Excuse me, does the current Mesh（NCS 3.2.4） support Directed Forwarding and Remote Provisioning? The examples in NCS 3.2.4 don’t seem to include configurations for the...
