Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I am running the example code:C:\nRF5_SDK_17.0.2_d674dde\examples\ble_central_and_peripheral\experimental\ble_app_multirole_lesc
I am using PCA10040 dev board.
When...
I am attempting to use a one shot application timer. This works fine when I use the event handler to perform a specific task toggle an LED for example. But I would really...
Good afternoon,
We have developed a new equipment based on the nrf52840. We use sofldevice 's140_nrf52_6.1.0_softdevice' and we use bonding with static pin.
We have setup...
Hi,
Is it possible to generate Complimentary PWM in nrF840? Do i need to use the PWM in Individual mode?
My application is a synchronous buck converter
thanks,
th...
Hi all,
I have RaspPi_OT_Border_Router_Demo_v4.1.0-1.alpha image for BorderRouter and need to work with Command lines in Command line Interface(CLI) and with diag commands...
Hello,
I have recently received nrf5340 development kit.
To get my very first stamps of programming given precompiled image peripheral heart rate, I
1. Connected board...
Hello,
I want to evaluate the ble_app_buttonless_dfu example (C:\nRF5SDK160098a08e\examples\ble_peripheral\ble_app_buttonless_dfu). I am using the nRF5 SDK 16.0.0, IAR EWARM...
I have an nRF52840 - install the BLE Sniffer Software on it - play a littel Bit - happy :-)
(dont help me to scan the communication between 2 devices - but thats a other...
Hi,
I need to test the data rate capacity between a nrf52840 and a smartphone. Smartphone being the central device and nrf52840 being the peripheral device. I have an...
Hi,
What hardware configuration settings that I need to change when moving from Development Kit(NRF52832) to BL651(NRF52810)?
I can run all examples from "nRF5_SDK_17...
Based on the datasheet table 166 can the drive strength for SCL/SDA pin is mentioned to be selected as S0D1 can it be changed to H0D1 drive strength? Since based on the IBIS...
Hi! What is the proper use of sd_ble_gap_adv_stop in SDK 15? I'm using nrf52832 in my application but can't seen to find a corret way to stop advertising.
Looking on ble_gap...
Hi all,
I'm using Raspberry Pi with Nordic dongle and flashed the Nordic Alpha 4.1.0.1 image to make it as BorderRouter in NCP design.
I have EFR32device and have flashed...
Hi
I'm using nrf52832 custom board with 14.2.0 SDK version and trying to communicate TWI interface with LTC2631 DAC converter. I tested my sensor hardware with Arduino and...
DK 52840 DK
description ： for example ：we use 52840 DK start a adv at 37 channel,when this packet transmission finished， the radio will change from TX to RX，so how we get...
