Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
we have deploy the serialization libraries in our host to communicate with nrf52840, but it seems the serialization libraries don't handle pairing/bonding event, so we can...
So I am doing a number of crypto operations. One of which for example is an ECDSA signing operation. I do that through mbedtls_ecdsa_write_signature which is using the CC310...
Hello,
We're currently evaluating the feasibility for leveraging our existing NRF51840 as host/system processor that runs all of our application code and runs the BLE...
Hi,
I am having some trouble. For a project, I need GPS, 9 axis IMU (accelerometer, gyroscope, and magnetometer), a microphone, and LTE connectivity in a small form factor...
Hi Team,
I am using nRF Connect SDK v1.3.0 tag for nRF52840 DK.
I am trying to integrate BLE HCI UART project files into Zigbee light switch project.
I have attached...
SDK : nRF5_SDK_for_Thread_and_Zigbee_v4.1.0
Hardware : 2x nRF52840 (PCA10059) + 1x generic overflow sensor.
This is an attempt to gather complete information regarding...
Hi,
I am using nRF52832 along with Softdevice 6.0.0, SDK 15.0.0, Chip Revision 2 (QFAA-EX0).
I am using nRF52832 as central device.
I see from sniffer that LL_VERSION_IND...
I have Power profiler kit 1 which was working fine. I have updated my nrfconnect app and since then on my power profiler kit, I am unable to perform battery power profiling...
Hi
I am trying to build the BLE Secure DFU Bootloader example using SDK 17.02 and the PCA10040 Dev board. Following various threads in the forum, I have been successful...
Hello, I'm trying to merge NFC writeable example " writable_ndef_msg " with BLE Beacon " ble_app_beacon ". My aim is to start BLE Beacon after the scanning of NFC. I have...
Hi, I've a timer configured by gpiote to capture with a second 'overflow' capture should the signal stop. I'm not using an interrupt instead the CC[0] value is being used...
I have seen the same issue reported.
nRF52840 DK does not appear as a removable drive named "JLINK"
Done the following.
1- My laptop has only one USB port. So I have...
Hi there, I'm controlling the nrf9160 with a esp32 and I'm wondering if you have an recommended libraries for forming AT commands and parsing the return messages?
I'm running through the nrf9160 dk startup guide and I've updated the application and modem firmware. However, it does not look like the application is accepting AT commands...
