Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hi all,
On the iOS version of the Blinky APP, there is a statement
Created by Mostafa Berg on 01/12/2017. Copyright 2017 Nordic Semiconductor ASA. All rights reserved...
Hi,
I am using pin 27 as SCL and 26 as SDA on my custom board which is working on 1.8V.
There is no activity on SCL pin, while i am getting correct values on SDA pin when...
How can I read the ICCID (Integrated Circuit Card ID) of the SIM-card?
Normally (with competitive modems) I get the CCID by AT+CCID.
The nRF9160 reponds with +CME: 0 ...
Hi, I would like to develop a BLE central node that sends over UART when a button is pressed. I understand the memory is limited on nRF52810, but I think it'll fit. The example...
I am developing on the nRF52832. I just discovered that if my program enables Access Port protection by writing the UICR at runtime, then the program can still be read out...
Hello,
I want to use a third party bluetooth module (based on Nordic SOC) in my application, so far my understanding is that using your softDevice stack I have to implement...
Hi
My Thingy:52 works perfectly OK with Thingy app on my iPhone.
However when I use the Gateway on my iPhone and then nrf cloud I get an unstable connection on the cloud...
Hello Developers,
I have just started playing around with BLE Mesh Zephyr examples on my recently purchased nRF52840-PDK board.
Anyways, I am bit stuck with one fundamental...
Hi,
I've used the nRF51822 in the past to make sensors that connect to a mobile device. Basically it worked just like every other non-mesh BLE device:
1. It advertised...
Hi:
I'm developing a project with nRF 58232 in ble_app_hrs_rscs_relay example ( s132 sdk:nRF5SDK160098a08e2 ). The device need to be central and peripheral,My device worked...
Hi there,
I'm planning and hoping to use the nRF52840 (in module form) for an upcoming medical device design.
This will need to interface to a PC/Mac/Linux to send specific...
Is APP_TIMER_V2 supported by Mesh SDK 4.1? According to this forum, v2 should fix all sorts of issues related to v1. But it seems that app_timer_mesh.c is only partially compatible...
Hey,
I am working on a version which is uploaded from a bootloader (DFU), the bootloader print to UART and uses the UART libraries.
I want the application to close the...
Hey,
I am working on nRF51822, SDK12, S130, I wish to get more data into my advertising packet, however there is not enough space, I was thinking to COMPLETELY remove...
