hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
I am using SDK 17 currently and nrf52840. I have read through the Q&As in the Dev zone and have not found the exact answer. So it might be a good idea to ask here
I understand...
I have set up a Beacon with nrf52840 and SDK 17. The Beacon signal is transmitted in 10s interval. The Beacon transmitter does not need to receive any response data. The default...
I was working on a modified version of Asset Tracker on thingy91.
Everything was working fine during the development and I almost finished the task needed and then I thought...
Hi,
could you please advise us on how to set a static MAC address for the nRF52 series? We haven't been able to find it in the documentation. And it seems that default is...
I have TWI sensor comms running fine in Zephyr on nrf52840_dk and separately Bluetooth controller in low latency mode using S140 softdevice also running fine in Zephyr on...
In SDK For Mesh 4.1.0 the Light LC/CTL/Lightness models were added. The problem with this addition is that another flash page is reserved for the models metadata and possible...
Hello,
I am trying to send something by my own via UARTE0. This is only for testing/learning purposes:
This is what I see:
[00:00:00.000,000] <info> app: enable...
Hi,
Can I control warm light as well as cool light using the CTL+LC server example provided in the Mesh SDK v4.2? Or does it support only warm light?
Moreover do we...
This is my log
Loading solution asset_tracker.emProject Executing load commands cmake -GNinja -DBOARD=nrf9160_pca10090ns -DBOARD_DIR=C:/Workspace/nRF9160/ncs/zephyr/boards...
Hi,
Currently I am setting up my work environment. I have a simple Zephyr project running on our custom board with the nRF52840, so a modified example and a custom board...
Hi Folks,
I am currently working on a BLE configuration composed of two NRF52840 chips. One is configured as central and the other as peripheral and use coded phy (long...
While I am going to pair with my android 9 Asus mobile phone with SDK 17 nRF52840. It in my mobile showing "Pairing rejected by Nordic_HRM". After that I have added a some...
Dear community,
I am trying to implement a custom service, however I am struggling because many example codes are for PCA10040, Softdevice S132 and/or for older SDK's. I...
Would it be possible to get the SHA256 hash for version 5.1.0 of the S132 soft device for the nRF52832? Just want to verify the integrity of the download. Thanks.
