I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
Hi,
Iam working on a project based on Ble Mesh, Iam using nrf5_SDK_for_Mesh_v4.2.0_src. Iam trying to form a BLE Mesh network and control the light bulb. I went through...
Hello Devs,
I am facing an difficult time to write a custom opcode to a QSPI flash memory. where I am trying to read the manufacture ID, it requires send the OP code + Address...
Hi, We are looking for a Suitable wireless technology for Video transfer(Video Transmitter and receiver)
Main Constraint: - From Power Up-->Boot-Up time of Wireless transmitter...
Hello,
We are looking for a 2.4Ghz supported module with Programmable Frequency Deviation. Is there a product that we can consider from Nordic Semiconductor for this?...
Hi, We are working with integrating LoRa to our nRF52840 with BLE and FreeRTOS. To be sure that LoRa worked as expected, we configured and tested LoRa on nRF52840 dk and observed...
Hello,
I'm using nrf52840 and i would like to ask if it possible to use the I2C bus without external pullups. I mean, i would like to avoid using external pullups
is there...
I am using a NRF52840 DK with a SoftDevice S140 6.1.1. I have also flashed the secure ble bootloader on the device.
I have been using the nrfprog command line tools within...
Hello,
Got the MQTT_SIMPLE to work and the sensor samples from zephyr also, however, how can i mix the 2 to have the mqttsimple with some gpio and i2c sensor ? how will...
Hi
I have installed every requirement for the device. I want to know how to run the blinky example on the device. I can not find the SDK which has the example plus can I...
Hello, I'm currently developing a PS2 code to read the inputs of a mouse and transmit it over BLE, nrf_delay_us() is giving me a fatal error every time according to debug...
Hi,
I am trying to implement Generic HID that can transmit/receive data like CDC using the generic HID example source of nRF52820 SDK 17.0.2.
But I can't do both sending...
Hello everyone,
I'm a fresher of nRF52833. I'm facing a problem like this:
I want to read some information in Terminal but In my product I only have USB I/Os (D+ D-)....
Hi,
I'm trying to use the nRF91 as a Modem for an Arduino. Is there some example on how to use the AT commands of the serial_lte_modem sample to send a HTTP (or at least...
I built an application for the nrf51822 on top of SDK12.3, to which I added the buttonless DFU based on the "experimental_ble_app_buttonless_dfu" example.
As a boot loader...
