I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
Hello,
I did a side by side comparison of the latest nrfutil v6.0.0a0 vs v5.2. It looks like v6.0.0a0 is much slower.
Looking at the log from the target device, it looks...
Hi,
I have installed Embedded Studio for ARM v4.22. However, the studio crashes when I select 'Activate Your Free License'. Reinstalling does not help, and neither a different...
Hi,
In order to read values from TH02 sensor(Address: 0x40) I first need to give a command i.e. write 0x01(for temperature) and 0x11(for RH) resp into internal CONFIG register...
What is the least expensive J-Link Model is required to program a nRF52840 on a custom commercial PCB?
I see that it is a ARM Cortex-M4 core, but I want to double-check...
Hi
Im using nRF52832-QAAB0. SDK 15.3. Softdevice is running.
With debugger connected, calling nrf_pwr_mgmt_shutdown(NRF_PWR_MGMT_SHUTDOWN_STAY_IN_SYSOFF) will assert in...
Hi everyone. Do you know any example of some over the air FW upgrade of nrf52832 chip via ESB protocol. As I understand it should be some combination of bootloader with DFU...
Hello,
We have selected nRF solution for our next product line and currently evaluating the software/SDK setup for that.
We are testing following SDKs:
nRF5_SDK_15.2...
in SDK 15.3.0, no eddystone lock event (NRF_BLE_ES_EVT_LOCK) is triggered after the unlock key was changed.
according the eddystone configuration specs:
A single byte...
I use example ble_app_uart, SoftDevice sdk 6.2.1, when receive data from bluetooth, then drive IO pin 18 to send infrared wave.
received data is Infrared raw formate, which...
Hi,
Our product uses Fanstel BM832 chip. As per https://www.bluetooth.com/develop-with-bluetooth/qualification-listing/qualification-listing-fees/ , should we opt for Innovation...
Hi
I am using TH02 for temp and RH measurement
I understand I must use TWI provided in SDK. However, I a working have c++ library(Wire.h) for I2C that I used with Arduino...
Dear All
I am right now working on BLE development with nRF52840DK. I checked a number of materials, including official specification from Bluetooth SIG, but none of them...
Hi,
I need to read a couple of external inputs - think buttons (although it's actually a sensor with relay output). It's for a prototype obviously.
I need to connect at...
Hello,
I have an application that advertise specific data. Data is long enough that I cannot fit my 128bit service UUID. I think of 3 options:
1. Use my service UUID but...
Whenever I store my data in Flash using FDS (Flash Data Storage Library) it stores a random value (but fixed) even though I am giving it a value.
I run the same thing in...
