Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
Hi,
The above pins are connected to test points in the ref schematic but stated as Nordic reserved in the pin description. Should I connect them to test points or can I...
I am wondering whether it is possible to maintain backwards compatibility for BL4 while also taking advantage of the BLE5 LR CODED PHY?
I am guessing I could scan in AUTO_PHY...
Hi,
What are the reasons for the nRF connect app or the nRF Mesh app or even the nRF UART app to connect to an Android phone?
I can see the DK advertising. I can see the...
Hi,
I am using nRF52832, SDK 15. My code is based on the freeRTOS code examples.
I am trying to Run my Task Every 10 ms. I tried to test this by using a counter to print...
Hi,
I have a problem with soft device. My code build well but when i try to compile it on nrf52840, i have below error:
Then i tried to go in boot loader:
Therefore...
Hi, Everyone
I have a product (named "A") developed on sdk12.3 and 52832.
This product has peripheral function and MTU Size is 64.
If I use "nRF Toolbox -> UART" on my smartphone...
Hi,
I'm working on the Mbed-OS USB HAL implementation for the nRF52840. I'm having a bit of difficulty getting the expectations of the USB stack to match up with the event...
Hi,
I completed the getting started guide (Getting Started Assistant app) of the nRF Connect v2.6.1:
I installed the toolchain, the SEGGER Embedded Studio and opened a...
Hello I am working through my project and ran into the roadblock of the nrf52840 not being able to use the 250kbit radio mode.
I tried a few workaround and ended up getting...
Hi,
I am working on the "pin_change_init" example to develop my interrupt based function.
I have added three pins/buttons into it and out of which only are working properly...
I AM AT THE END OF MY SANITY!!!
I have tried everything. SEGGER, Keil, installed J-link like 5 times, Python, nRFgo, nRF Connect for Desktop, nRF5x Command Line Tools...
Hello,
We are using nRF52840 with SES sdk 15.0 version. My other thread is here in that got problem with nrf_cal_set_callback(calendar_updated, test_Interval); this function...
I am trying to use a sensor that needs 9600 baud rate with the nRF52840-DK. I've set the baud rate to 9600 on the sdk_config.h. Would I still be able to see the transmit/receive...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Hello
I am using Segger Embedded Studio with nrf9160. I can 'Build and Run' the 'asset_tracker' project but the LEDs are not blinking and my development kit is not connecting...
