hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
WIth the upgrade to the new SDK, registering the callback handlers has been made more difficult to figure out.
The .sdh_ble_observers, .sdh_soc_observersers sections are...
Dear Sirs!
On one from 25 boards there is offset in ADC input about 30 ADC units. Vref = 0.6 V, Gain=6, 12 Bit ADC, oversampling 256 sample.
In other devices I do not...
Hi, Could you send me a sample to send "Hello World!" string from sender task to receiver task?
I am using C:\Nordic_Semi\nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral...
Hi, I have a question regarding the behaviour of a button in the nRF App in Android, sometimes the button "READ STATE" in the "Generic On Off Server" configuration changes...
Hi,
I have managed to run DFU mesh example and successfully updated firmware of whole mesh network. Now i am looking for options to perform customized DFU over mesh . Lets...
We are experiencing issues with nrfutil being flagged as containing malware, see screenshot below. Has Nordic experienced this before, is there something we can do to stop...
Hi
I have reported this before and now that you are a quarter away from a fully featured mesh sdk can I ask you to please enhance the SDK so that you supply a function that...
I'm evaluating possibilities of BLE-LESC Pairing/Bonding with the ble_app_hrs peripheral on the nRF52840-DK with SDK 12.3 and SoftDevice s132. To see what's going on in the...
Is it possible to flash multiple custom boards using sagger DKs at the same time?, assume 2 custom boards and 2 DKs, would they be able to flash the custom boards in parallel...
There are many places in the file fsm.c that have this compile condition check
#if defined FSM_DEBUG
blabla
#endif
that is wrong. The compiler will ignore it. There...
Dear Nordic,
Hello, I have to configure 2 UART. I have saw this post .
however, I have made a demo version for the project without 2 UART function, so I hope to apply...
Hello, I´m trying to compile the BLE Heart Rate service projects using SEGGER Embedded Studio. After importing the project from nrf52 SDK, I tried building the project but...
Hello,
I want to implement home automation project using 3 nRF52840 dongles. i.e I want to connect all the 3 dongles with each other and the signal sent from one device...
Hello, I am trying to design a product based on BLE MESH. I would need gateway to be able to accumulate data from network and send it outside. I need that gateway to connect...
