I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hello All,
we want to calculate the total power consumption when the controller is put on SYSTEM ON low power mode. Do you have any information on the way to do this? ...
My Central is willing to perform a bond ( pairing with bond ) to a Peripheral.
As an example and according to
Message Sequence Chart > Central Security Procedures >...
I have some copy jlink, they can used in keil and JFlash.exe, but can not use in nRFgoStudio.exe, is it right? nRFgoStudio can not support copy jlink edition?
Hi,
i have a wierd behavior on my board.
On my nrf52832 custom board i have sdk14.1 with DEBUG flag and NRF_LOG enabled.
Usualy when my board crash i got into some kind...
Hi.
I have RF communication between nRF24L01 + and nRF24LU1 +.
Incorrect data is transmitted occasionally during communication.
So, I want to use CRC, but when CRC...
I want to get 32000 bytes per second with NRF24LU1+ ,as my audio sampling rate is 16K and sampling bits is 16.But actually I have lost one packet or more per 10ms. data loss...
Hi Everyone,
Is it possible to programmatically assign a static mesh-local EID IPv6 address to a node in a network? I would like to communicate to individual nodes in the...
I am using the nRF52832 Soc, and have a requirement of using a timer with a large timeout value, hence I want to use the watchdog timer.But as I get TIMEOUT interrupt the...
Hello!
I need sensitive gpio.
I want that is gpio rising in 20[nsec].
However, the test results using the function below show that the gpio rise time is 200 nsec...
Hi,
I am new to the BLE environment. I am trying to connect my smart phone with nRF52832 development kit over BLE. Here, my smart phone should be able to send some user...
I am looking to extend the RTC beyond 24 bits using the Overflow interrupt.
The code in the rtc handler would look like:
static void rtc_handler(nrf_drv_rtc_int_type_t...
I have been trying to install the new version of everything Nordic 52.
That starts with the MDK 5.18.
To make sure I don't have an update problem I do a clean install...
Hi,
I want to know about mathematical formula to find / estimate the battery life of Bluetooth beacon containing NRF8240. If chip is transmitting at +8 dBm and have 1000...
Hi,
I add the NUS in the ble_app_hids_mouse example which the sdk version is 14.0.
There are four services in the project: dis, bas, hids and nus.
When I connceted the...
