The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
We wanted to share our feedback as we recently went through Zigbee 3.0.1 BDB/cluster certification using the ZBOSS with our end device product. While we were ultimately able...
I just got a new set of nRF5340 Audio DKs and I may have been too fast on the trigger trying to flash the boards with example programs. I'm using VS Code, and I'm a newbie...
I want to know where did the "desired_data_size" value in le_audio_rx_data_handler come from?
And why "data_size != desired_data_size" means the pkt is bad frame?
Thank...
Hi,
We have recently acquired a new firmware engineer, and would like to get him set up with a development environment for developing code for our product. The problem...
Code running on nRF52833 devkit version 1.0.0 that continuously sends an empty 500 kbit/s radio packet:
Code running on nRF54L15 devkit version 0.8.1 with chip revision...
NCS v2.8.0
nRF52832 DK & nRF52840 DK
peripheral_uart unmodified example
nRF52832 DK with peripheral_uart example has about 1.3 mA current when LED off and sleep mode...
We want to use a BL6554PA (based on the nRF52840) as a thread node and enable the integrated Skyworks SKY66112-11 front-end module with PA and LNA to increase our range. I...
Hi All.
Trying to complete Lesson 6 Exercise 2 from the course nRF Connect SDK Fundamentals made by the DevAcadeny, I connected the Thingy53 to my computer through USB-C...
Hi,
As part of some verification purposes, we need to test out peripheral with the nRF connect Bluetooth low energy app. We have the peripheral set to 2M, DLE enabled and...
Dear Nordic-Support and community,
I am developing a system where a Thingy91 device needs to:
Dynamically connect to a specific BLE device that sends data like Heart...
In version 2.9.0, I modified the JEDEC ID.
The system is supposed to send a "Deep power- down enter(0xB9)" command after reading the JEDEC ID.
However, after the system...
Hi,
I am trying to evaluate the provided smp_svr sample with the BLE DFU on the NRF52840 dongle after I have already tested it on the DK.
I get the following error message...
If we subscribe all attributes of cluster of device connects to coordinator will it make issue? we have noticed its dropping many values if subscribed at same time. if values...
Hi,
I'm working with a custom board build with an nrf9161, I've created my board from nrf9161dk board (change some pin and defintion), I'm able to flash and build? I can...
Hello all,
I'm working on nRF-9160 and nRF-9151.
What I want to add into SLM application were:
Configure to communicate through UART2 since it will be working with...
