hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello Nordic Forum,
Thank you in advance for your help. I have a BMA400 accelerometer break out board which I am able to connect and get to work with arduino.
I am now...
New to nrf52.
Looking for a way to identify radio traffic, to be able to distinguish BLE from 802.15.4 and 802.11. I'm not looking for a full fledged sniffer or looking...
Hi, Nordic Support Team,
I am writing to request your assistance regarding some test failures encountered during the UL certification process for a Matter 1.5.0 product...
Hey,
I am developing an app on a custom board with the nRF9160 which already works in low power. It draws approx. 12uA which is ok for me. Now I need to introduce UART communication...
hi I want to use nrf connect sdk using VS code and i want to start my development on this, now i am unable to install this in my windows 11
1. I have installed this nrf...
Had an interresting issue that we have resolved, but we're trying to understand...
We had a timer (TIMER2) running and matching towards CC[3] every 500us. This match results...
So, I have compiled blinky for the USB dongle52840, but am having difficulty getting west or the development toolchain to flash the dongle. Any help would be appteciated....
I have a custom nrf52833 based board that I tried programming over the integrated JLink on then nrf52 dk via swd. All attempts to program or recover the board failed with...
I was using the PPK2 kit yesterday and I tried the power profiler on nRF Connect (not working with any DUT). I was looking at various apps provied on nRF Connect, I was on...
Hello,
I am developing a project on the nRF54L15 and encountered a system hang when using two UART instances simultaneously: UART20 (for logging and printk ) and UART30...
Hi
I am wondering when I use this function, how much time do I need between I set a TXP and a TXP has been successfully updated. I am developing an application that needs...
I try to set custom compiler flags for the whole project including Zephyr via prj.conf / CONFIG_COMPILER_OPT to compute worst case stack usage as follows: CONFIG_COMPILER_OPT...
Hi all,
I am having difficulties reading microphone data using built-in microphone at Xiao Seeed nRF52840 Sense. I have configured the overlay file as suggested here . Then...
Hello,
I am following the cellular IoT fundamental course with nRF9151-DK.
I didn't have any issue until Lesson 7, but I found that the screen shot of the lesson is...
