The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Here is what I want : - a nrf52833 that advertises as coded phy - another device than needs to scan and connect to the first in coded phy On my nrf52833, s140 7.3.0, I successfuly...
Hi team,
I am trying to work on SPI peripheral on the nordic development board nRF52840. How many SPI compatible ICs are present on the board. And how to identify them?...
Hi,
I’m trying to understand the bigger picture related to BLE Audio in order to create a simple wildlife monitoring project. The hardware I’m thinking about is a nRF5340...
In the release notes for mfw_nrf9160_1.3.2 it says "This release is aligned with v2.1 of nRF91 AT command reference guide." And new functionality: "- Feature to output GNSS...
Hello, Nordicsemi community,
I am a bit confused about how I need to proceed in order to use both cores in my nRF5340 that lives in a custom board.
I was playing with...
Hi,
We are developing a product with an nRF528322 that should be able to perform a DFU on an external microcontroller by receiving the firmware over BLE and then sending...
Hello,
i'm using nRF5 SDK 17.0.2and nRF5 SDK for Mesh v5.0.0 using the examples sensor client and server.
I am trying to create a function that makes the client client...
Hello,
is it possible to see periodic advertisement packets (AUX_SYNC_IND and AUX_CHAIN_IND) when sniffing the normal periodic_adv sample (running on 52840DK) with a 52840...
Hi all.
I have a problem when employing QRS peak detection library on github to my NRF52840 board.
i just add the PanTompkin.c and PanTompkin.h into my project without...
I'm just redesigning a circuit using the nRF9160 and wanted a second opinion on this.
I am no longer using the GPS antenna on this chip, and I want to make sure this antenna...
I am in the process of migrating a project using the nrf5340 from nRF Connect SDK v1.6.0 to v2.2.0 .
I have run into an issue where gpio pins I could use before are no longer...
Hi There.
I'm using the Asset Trackerv2 as a base for my application.
If I provision certificates at boot pior to enabling the LTE connection. the GNSS is never enabled...
Hi,
I'm trying to develop an application that uses an nrf52840-dk board and the pc-ble-driver-py. The dk is supposed to be a central device.
Using the python driver library...
1 I didn't understand ANT on nRF5340 under Highlights. I didn't find the introduction I thought of in the following article.
2 Added the CONFIG_ESB_DYNAMIC_INTERRUPTS Kconfig...
