Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi all,
I recently installed the nRF Connect SDK and have had some success. Very snazzy.
I have seen some issues with the JLink on the DK resetting during firmware validation...
I cannot seem to get floating point supoort for printf/scranf
It works for LOG_INF
I have tried the following .conf settings:
CONFIG_NEWLIB_LIBC =y
CONFIG_NEWLIB_LIBC_FLOAT_PRINTF...
Hi All!
I am trying to program the external nrf9160 SOC using nrf9160 DK using the following connections. Before that, I tried the same connections to program the nrf52820...
When I set CONFIG_LOG=y, CONFIG_SERIAL=y in prj.conf, the UART streams out diagnostic message from my application code as expected, but I also get this endless I2C error message...
I am using NRF52832 for my project.
Refer the following Softdevice and SDK versions.
Softdevice: S132_2.0.0-7.alpha
SDK Version: 4.0.0-2.alpha
Question 1:...
I am using nRF Connect SDK 1.9.0 and the NRF52840.
When building samples/keys/hw_unique_key you get this warning:
----------------------------------------------------...
Hi,
My nRF52840 dongle which was working fine in the past doesn't seem to be responding properly. Is there anything I can do?
Some background:
1 - I have used it...
When we test the matter, we sometimes will meet commissioning accessory fail and network dropping. In the worst case, we can't access the network for a long time after the...
NRF_SO_RAI_NO_DATA AT#XSOCKETOPT=1,50 does not cause RRC release as expected, instead hipower LTE continues another ~20s. https://github.com/nrfconnect/sdk-nrfxlib/blob/main...
nRF52840, SDK 17.0.2, SD140 v7.0.1
My firmware application is happily sleeping via calls to nrf_pwr_mgmt_run(), waking up to service interrupts and do work, then going...
I have not been able to get the nRF52840 ncs v2.0.2 watchdog not to reset.
I tried kicking the watchdog every second and can set a break point and see that the kick does...
Hi all,
I'm looking for an SDK function that will tell me if my device is connected to BLE
from this post 8 years ago the answer is no, has something changed in those...
I am using the 9160 to develop a product for the customer. Its sdk version is ncs1.9.0, and the firmware version of the modem is v1.3.1. The device needs to download data...
Since sensor.h API in Zephyr does not support reading hw FIFO, I am planning to use SPI driver to read the hw FIFO on received an interrupt when FIFO has data.
Is there...
