hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hi,
We are trying to integrate a remote controller functionality for smart TV and set-top box etc, using our product based on nRF52832(nRF5 SDK). I understand that we can...
I am trying to use a SPI bus with three MAX3109 chips attached to give me 6 UARTS. My overlay is defined as follows:
& spi1 {
cs-gpios = <& gpio1 13 GPIO_ACTIVE_LOW...
Hello, I'm working on a s332 application and I need to include the DFU feature in the code. I've managed to perform a DFU on s132 applications following examples like this...
I've built and able to the run the 802.15.4 RF Phy Tester but it doesn't seen to recognize any of the custom commands. Can you provide more insight into this please?
Please ignore Product Type I selected - i set it to just select that to something.
I'm planning/designing a comm box, which needs to speak to ZigBee based nodes/sensors...
Hello
I'm a beginner. I am using NRF52 series and coding in segger embedded studio. I have modified the ble_uart example and added some extra code so that I get the sensors...
Hi,
My customer occur a problem with nRF5 SDK10.0.0, the sample ble_app_hids_keyboard.
We test the sample on nRF51DK.
We connect the DK with an Android phone, and bonded...
Hello, I downloaded the NRF5 SDK for mesh. I want to make the light switch example. I installed the server and client software on two different cards. I want to make the necessary...
I am using NRF9160 (PCA10090, 1.0.0, 2021.7) for my experiment using the .hex file of UDP example provided here ( https://devzone.nordicsemi.com/nordic/cellular-iot-guides...
Hi
I use the nRF52840 board and am currently working on a Matter project.
I am trying to add a cluster to an existing Matter sample project as per the link guide below...
Hi,
I am working on pdm mic integration in zephyr RTOS. I used INMP441 mic sensor. I got SPL in dB by using nrfx. I want to create a driver for this mic. Please help me...
I have an nrf21540-ek. I hope it can be used with my nrf5340-dk. Does NCS 2.0.0 contain relevant drivers or does the driver need to be implemented by me? If NCS 2.0 contains...
Hi, recently I am been consistently getting the same issue as this post, despite having successful performed the Mesh DFU in the past and with the example code:
I suspect...
Hello,
My goal is to make DFU over a mesh network.
Using this guide , I did the following:
nrfjprog --program bin/softdevice/s132_nrf52_7.2.0_softdevice.hex --chiperase...
