hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
I've tested two scenarios using a hardware loopback to test UART functionality. The double buffer approach does not work as expected.
SDK version 1.6.1
CONFIG_SERIAL=y...
Hi,
I used nRF91DK for almost 2 months non stop to debug the final nRF91 based board for our air quality monitoring hardware to fight the propagation of Covid virus.
But...
I tested various copy methods in terms of instruction cycles, that I determined with DWT.
For that I copied an uint8_t array size 70 by
for Loop --> 63 Cycles
memcpy...
Hello,
I am using nRF52840 dev kit with sdk 17.0.2, s140 softdevice and dfu bootloader also implemented.
When I download the firmware to dev kit it works as intended...
Hi,
i am working on nRF52832. i am facing a issue of RESET when i call advertise_start() again after advertise duration. in debug it shows fatal error.
Hi there,
I've installed and followed the nRF Connect SDK manual install getting started guide ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/gs_installing...
I'm using 52832 as a Central(SDK_17.0.2/S132_7.0.2), and sometimes get a connect-disconnect failure with reason 0x3e.It happens randomly and frequently.
I search the forum...
Hi Supportteam,
i am trying to use Release Assistance Indication (RAI) to shorten the RRC-Connected using nRF9160 DK.
I'm enabling REL14FEAT with the following AT commands...
Hello, sir.
I used to work on twi0 and twi1, but now I'd want to shift both twim0 and twim1. However, I'm getting an error saying that 'NRFX TWIM1 INST IDX' is undeclared...
Is it possible for nRF Connect iOS app to display devices that were connected/paired through the iOS Settings menu? The problem I am having is when looking to perform DFU...
Hi iBasis support,
I'm having a billing issue with your website. I'm using the iBasis card with the NRF9160DK board.
When I ran out of data, I just follow the link on...
Right now I use the app_timer_cnt_get() method to get a current tick count. It appears to return a counter that increases with 32768 counts per second. However, it overflows...
Hi,
In NRF52832 i have integrated IMU sensor and and DPS sensor . i have build code and Run .
But after 2-3 minutes its stucked . so then i pressed the pause button ....
