Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
I have successfully installed the drivers and downloaded the latest firmware version, but the connexion fails and I can not use the AT interfaces command for the modem controller...
Hi
I am using an example project written for pca_10040, I am trying to replace it with pca_10010.
So far, I changed the "Target Device" in the project options and the...
Hi all,
Currently we are trying to measure the power of nRF52832 using (1) nRF52 DK board, (2) power profiler kit 2 (PPK2).
We used PPK2 in source-meter mode and we connected...
Shalom!
I have a custom nRF9160 board with uart0 connected to the outside world by RS232. I set the uart0 as the printk() debug output. I also need to write and read binary...
I get that is has to do with something around the MSB. But I cant seem to find a way to prevent this. No i can not send a byte 0x00 since this will trigger certaint behavior...
Hi,
I am developing an Openthread application using Nordic Connect SDK for the nrf52840dongle. I updated my nrf SDK to bd075cc09. Since then, my application won't boot anymore...
Hi,
I need to switch DK to 3v as my custom board has 3v.
When I switch VDD_IO to 3v board doesn't start at all. LED5 blinks for a moment but nothing happens.
Switching...
Hi,
I am currently working on an internal dfu modeled after the secure_bootloader_uart/ example in SDK 15.3.0. I have gotten the dfu to perform a successful dfu with the...
Hi!
I am developing on a custom board and only have the Debug in connector P3 from nrf9160dk to debug the board. I want to send AT commands to configure the modem and will...
I am a systems engineer helping my team in the component selection phase of the project that involves BLE communication between our master side and a simple remote control...
I have issue to program nrf52832 with nrfjprog command line.
my program use nrf52formesh sdk. I developed with Segger Embedded Studio with GCC on the Linux PC. I modified...
Hello all,
I have successfully installed nRF Connect, nRF Connect SDK v1.6.0 and SEGGER Embedded Studio (SES) v5.50.c to run and debug some samples on my nRF5340 Development...
Hello everyone,
I CAN NOT include the ocrypto_ecdsa_p256_public_key.h file into my project.
What are configurations I need to enable?
I'm new to NCS, could you provide...
Hi, Nordic
This is the test result that I use nRF52833 as the host to connect the slave, slave txpower = 0dbm.
And use Wireshart Sniffer to grab the air packet when...
