Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
I am trying to implement the buttonless dfu example, I successfully managed to upload the template example examples\ble_peripheral\ble_app_buttonless_dfu and can see it advertising...
Hi all,
I'm working on a limited power budget system. MSP430 is the master that is supplying power to nrf51882 (slave). Every 2s MSP430 derives a pin high to drive the nrf51...
nrf9160 modem Firmware version 1.3.0 release listed nidd or non-ip support. in the firmware.
We are eager to use this feature to send/receive data over RF control plane...
"CTE can be used in both connectionless and connection-oriented scenarios. For connectionless use, the periodic advertising feature is required (since deterministic timing...
Hello all,
I'm using NRF52840 with last sdk (V1.6.0) of nrf connect but I can't put the device into sleep mode (where the current consumption is at about 3/4 U) the device...
Hi,
I need a 1Hz clock with its interrupt function.
Where do I find an example to set the timer RTC0 or RTC1 to 1Hz and how to set the timer callback function?
Thanks...
Hi,
I am using nrfx_twim driver, and I want to read value from sensor's register. When I want to do that sequence looks something like this:
(SENSOR_I2c_ADDR+Read_bit...
Hello Sirs
I have two questions about the nrf5340-dk evaluation board.
The first one is how can I get the scan data of an advertising device?
And the second is that...
Hi,
My dev environment is as follows:
nrf52840 + s140 +SD7.0.1 + SDK17.0.0.9 + SES + nrfutil v6.1.0
I started my development for DFU and utilized secure buttonless DFU...
Hi there,
Currently, I am getting an error with a low power node when the remote cannot configure through another regular node in a mesh network. What causes me to get this...
Hello Nordic support,
I would like to use the APIs in IEEE 802.15.4, especially mlme_scan_req in nRF5 SDK for Thread & Zigbee for a ZigBee application in order to scan for...
I want to use the Nordic UART/Serial Port Emulation over BLE to communicate to a windows or linux host computer.
I see Andriod and IOS haveapps available to support Nordic...
Hello,
I have upgraded my project from nRF_Connect 1.5.1 to nRF_Connect 1.6.0.
It runs on nRF9160 and I use RTT viewer v7.50a.
The problem that I see is that the logs...
Hi everyone,
To give a first introduction, I have been working with this development kit for a while now. I'm trying to develop a Zigbee device and I'm very close to finishing...
Hi,
I want to scan for broadcast messages from a specific device that I never connect to (not bonded to for sure) and I want to filter out messages from other devices! to...
