Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
Hello
I am using sdk v17. I am merging the example of ble_app_uart and crypto_aes_ctr.
I added files about crypto and set the file path. However, the path error is printed...
Hello~
I am experiencing hardfault occasionally. (once a day ~ once in 3 days)
I am testing 14 boards to catch hardfault.
The following is my setup
- hardware...
Hello, I was trying to run the sample Alexa Gadget Application on my NR52840-DK, using nrf Connect SDK v1.5.0. However, upon trying to run the application I am getting the...
Hi support team,
I am developing a product. The product needs read adc and restart advertising when no connection.
I get hardfault randomly when called the ble_advertising_start...
Hi all, the application i'm using nRF52810 for requires that I keep the device powered on all the time. However, in the case of errors (tolerable within my application) I...
I successfully compiled the micro_ecc library, but when I try to compile the project with it, I get an error. Has anyone encountered this? What can be wrong?
Build target...
We use the nRF5340 D version IC for one project, but the PCBA (main chip is nRF5340) not working, we can burn the hello_world.hex by Jlink 7.23 version, But the Crystal 32...
We are implementing on nRF52840 with latest NCS version the following code:
The nvs_init() function is halting due to an error at flash_sync_mpsl.c within nrf_flash_sync_exe...
Hello,
We are working on the nrf52840 custom board in that We trying to update firmware via DFU.
Problem definition : First we update firmware via DFU application boot...
Hi ,
We have a custom hardware with an Active GPS Antenna (that is connected to the main board with u.fl connector).
I ran the GPS SNR command to test the performance...
I'm designing a PCB that uses the nrf52832 with an external RTC, the DS1339 ( https://datasheets.maximintegrated.com/en/ds/DS1339-DS1339U.pdf ). I want to use a single 3.3V...
I'm enabling external power off warnings, as specified in section 5.22 of the AT command guide.
When I drop the supply voltage I see a LTE network disconnected message from...
Hello Nordic!
I have been developing a Zigbee application and now, I need to connect via Serial communication with another device. I just need to listen to the port, not...
I am using flash_fstorage_s140_pca10056 example from SDK v17.0.2 , I see that the start address is 0x0003 E000 and the end address is 0x0003 EFFF respectively.
I want to...
