hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
I'm working in migration from nRF51 to nRF52 and nrfx drivers. But now stucking in the errors. There are much errors, but all of that seem to be simulaly caused by the no...
Hello,
I am working on a sensor which requires data transfer over with data length over 255 bytes. I am using nRF52832 uC and and from what I see from nordic infocenter...
Hi,
We are using the nRF Connect for Desktop app to update production devices to the latest FW version of our application. I (on Windows) am normally the only person in...
Hello
I'm trying to add zigbee to an existing freeRTOS project with BLE. The approach so far is combining "Zigbee Multi Sensor with FreeRTOS Example" and "Adding dynamic...
Hi.
I am writing software for my custom nRF52832 device but hardware wise it is identical to the nRF52 DK.
I'm not that good of an embedded coder (or any kind of coder...
Hello
In my application (based on ble_thread_dyn_mtd_coap_cli example), I would like to get the list of devices present on the network (ip).
I saw that there was a command...
Dear all,
My CMW500 have NB-IOT option only (NO CAT-M option is installed) and I would like to see how to setup CMW500 (NB-IOT mode ONLY) to communicate with Thingy91DK...
We are using Enhanced Shockbust and would like to maximize the operating range. We noticed this footnote on page 356 of the latest spec sheet (v1.1):
Typical sensitivity...
Hi,
I'm trying to reduce latency when relaying BLE packets. The goal is to have a couple of wireless peripherals connected to a hub talking BLE with a central, with minimal...
Hi,
I am trying to implement LC server for my lights. I want to make the RUN level of the LC model configurable i.e, change the RUN level according to the user need.
Can...
There was an unexpected issue configuring beacon ad packages. The task is to transfer as much data as possible in beacon mode. For this, I want to include the scan responce...
The chip we use is nrf52832 and the SDK is nrf5_ SDK_ 15.3.0_ 59ac345, Can we use nrf Toolbox (version: 2.7.2) to upgrade bootloader? 1. How to make bootloader upgrade package...
hi,
I have nrf52840 DK and a dongle and I would like to connect the dongle to android device and scan for the DK in coded phy.
where can I find some SDK for using the...
Hi,
From previous case , I still not fully understand how chip to retrieve the calibrated data from flash(already implemented read/write data for the interface by FDS),...
This question stems from this discussion
https://devzone.nordicsemi.com/f/nordic-q-a/71044/notifications-how-to-know-who-is-consuming-tx-buffers-most-efficient-way-of-sending...
