Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Hi,
I have a question about the tolerance on the VDD voltage. In the datasheet it says: "RF 3GPP compliancy requires 3.3V."
I am wondering if there is more specific...
Hey all,
So I am a beginner and haven't work with this environment a lot. I use SES to debug and upload application to the nrf9160. I can allready upload some basic application...
Hello, I have three nrf52840 development boards and one pcb that I made myself using nrf52840. I want to find the location of my pcb with a demo using these development boards...
Hello,
Softdevice: 7.0.1, SDK: 16.0, Device: nRF52840
In the production, we want to save time programming the devices. So I'm using following command to combine bootloader...
Setup : I am using android-ble-library for my android app. I am using modified blinky example on embedded side. I have tried following implementation on android app:
I...
I have two nrf51822 devices, one running s110, the other s120. The s110 device reads ADC values every 20ms, and if they changed from the last reading it sends a notification...
Hello,
The following define is present in file nrf_sdm.h, SDK 17.0.2:
#define SD_FLASH_SIZE 0x26000
I think it's wrong, it shall be 0x27000. But it's maybe not used...
I am working with a IC that requires SPI clocks to be synchronized (in phase) with its system clock. Currently the IC's clock source is connected to one of the nRF52's GPIO...
problem: in BLE data length negotiation , In the response from slave tx doesnt go above 216 , and rx doesnot go above 54 .
s140
Experimental UDP example - sdk v16.0 (...
Hi.
I'm pretty new with SEGGER Embedded Studio and with nRF9160 dk.
I would to receive time with NTP serveur but I'm lost.
I don't know what to use. if it is better...
Hi, I am working on nrf52840 and I am trying to enable the repeated pairing attempt protection. (PM_RA_PROTECTION) After enabling the module I can see the logs telling me...
Hi All,
I want to create a Thread network with multiple OTBRs, which is based on two nRF52840 run Thread RCP hex provided by Nordic SDK.
I created the thread network by...
Hi there,
I would like to set my dongle into DFU mode from software, I am using the USB-CDC-ACM class, and the softdevice as a central device.
Ideally I would send a...
Hello,
in our project we have a nRF52840DK as central and a nRF52832 chip on a custom board as peripheral. The software on the nRF52840DK is based on the ble_app_uart_c...
Hello
I use mpu6050 and I want to use a 'Complementary Filter' to get the angle of the X, Y, and Z axes.
Applying this filter to the value of mpu6050 seems to reduce...
