Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
I'm using the ble_app_grs_freertos example. I'm trying to maximize its thru-put potential for Central devices which can support the high data rates. For this I've used the...
Hi, guys,
What I do:
Add freeRTOS into ble_app_hrs example project in SDK15.0
What matter I get:
When I set NRF_SDH_BLE_GATT_MAX_MTU_SIZE as 247, the device can not...
Hi Guys,
I am using Si7021 I2C temperature sensor and I want to read the temperature value using nrf52840-DK. I connected the sensor to the 27,26 pin.
I wanted to read...
DK version: nRF5_SDK_15.0.0_a53641a
Softdevice version: s132_nrf52_6.0.0_softdevice
I am using a Fanstel BT832X SOC, which has the SKY66112 PA, on a custom PCB. The...
Hello,
I am using UART to receive data on a nRF52840 DK.
I have written some code using the Serial Port Library.
I have attached snippets of the code dealing with the...
Hi,
I'm working on a tone library. I'm using timer2 and ppi channels to generate 50% pwm signal.
It's working fine.
Now i want to add another timer comparison ( timeout...
I am trying to see if there is a way I can generate a multi frequency audio signal without additional hardware. I am talking about something similar to DTMF. The audio wave...
Would you please tell me how to use the nrf52832 PWM interface to implement differential output to spkr?
Here is my PWM interface configuration code:
NRF_PWM0->PSEL...
I am working on a device which also needs to give audio feedback to the user.
The app on the mobile phone needs to send a wav (or similar) file (mono, speech) to the device...
hi, I am using nrf52832 development board for PWM and I want to play an audio (.wav) file using PWM, I am unable to play the audio clip using the PWM, and same audio file...
Hello,
I'm using SDK15.3 and trying to do a non-connectable advertising while connected.
For that I set my adv package as non-connectable, however, when I run the function...
Dear Nordic Team,
I have a BLE application that we developed on nRF52840 DK for S140 based SoC and this application is working fine on the DK Board.
Now we would like...
I am using IAR version 8.30.2 . When I try to build the example project is the nRF5_SDK_15.3.0_59ac345 for 802.15.4 for the wireless UART I get a build error:
wchar_t in...
When I start my nRF9160 modem (AT+CFUN=1) it can sit in CEREG mode 4 (unknown) for a couple of minutes, before it switches to 2 (searching) then 1 (registered).
Is that...
