Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Next week, we have a meeting with our customer to give them an overview on all our BLE solutions (they are interested in module) but I also want to give them an overview on...
nrf52832, SDK 15.0.0
I develop the project based on the example 'ble_app_buttonless_dfu'
But when I want to add some peripherals, such as SAADC, SPI and PPI, and some...
I'm seeing strange corruption in the nrf52840 virtual COM/UART (the one that goes through USB and the JLink interface MCU).
The nrf52840 is running the UART serialization...
I had setup nRF sniffer with below software and hardware, but the Wireshark seen unable capture BLE data.
nRF Sniffer software nrf_sniffer_2.0.0-beta-1_51296aa.zip ...
I would like to use the time library to manage multiple times with different timezones in my embedded system.
I have already seen the ble_app_cts_c example and the nrf5...
this is vishal from VVDN tech working as a Hardware design engineer .
In our project we are going to use 10k module of LTE EC25E.
So we need step file from your side ...
Hello,
In ble_app_blinky code,I cant understand this line "#define APP_BLE_OBSERVER_PRIO 3" and what does the value 3 represents here??. Is this value constant or can be...
Hi,
We have been developing our system around nRF52840 and we are now looking closer into the real-time performance of the MCU & SDK. The scenario is simple: a signal ‘YELLOW...
I am trying to add the valid range descriptor to my measurement interval characteristic in the Health Thermometer. This is a necessary step as my measurement interval characteristic...
Hi
I am using the ble_app_blinky's lbs application, as found here in the 14.2 service
C:\Eran\Software\Nordic\Packages\nRF5_SDK_14.2.0_17b948a\nRF5_SDK_14.2.0_17b948a...
Hello,
We have an application on Iphone running with our custom service :
uuid : 0000fdF9-0000-1000-8000-00805f9b34fb
and our characteristics :
char-handle 0x16...
Dear Sir, we are developing an application on the nRF52840 kit with SDK 15.0.0. We are using Keil as compiler. In our application we need to receive data from two uart together...
Hi Everyone,
I have two task in which i am receving data from bluetooth and if i receive a particular hex value , i want a task(which is Toggling LED State) to run on...
Hi,
I am trying to to port ble-mesh code (serial example) into ble_app_uart. I am using nrf5_SDK_forMesh_v2.1.1 and nRF5_SDK_15.0.0_a53641a on DK-N52832.
After merging...
