nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Dear Team,
We are registering with https://imports.gov.in/MEITY/public/home for nrf7002 modules which were sent by Nordic team through DHL.
Please send us the IC code...
Hello,
I am currently working on nrf52832 and trying to change the sampling frequency to 10KHz ,ie, 100us and keeping buffer samples as 1.
Previously in the example we...
In the product specification of nPM1100, for fixed 500mA charging limit, ISET should be connected to VSYS. In the USB-configuration (Configuration 3) ISET is connected to...
Hi:
We want to test the nrf7002 WIFI performance based on the nrf7002 PDK.Do we have relevant test firmware?
We noticed that the sdk document of V2.1.2 has a description...
hi.
I have a firmware using standard GATT, now im implementing the mesh layer.
Im using SDK 17.0.2 + MESH 5.0.0. (im not using the new sdk connect because it is very difficult...
I'm moving from NRF9160DK to a custom board, where it has no UART. I plan to just use RTT for debugging messages.
However, I found if I delete the section which defines...
Hi,
I build secure_bootloader_ble_s132_pca10040_debug example (SDK17.1) on SES 6.30.
The only modification to the project is excluding SEGGER_RTT_Syscalls_SES.c.
...
It is possible to addressing nodes using MAC address of the device in Thread network?
In topology: PC <-> Border router <-> Thread mesh nodes
which IPv6 (Mesh-Local EID...
Hello
I'm new to the nrf platform and wanted to try out the I2C functionality of my nrf5340 DK. The only example I could find was the Fujitsu MB85RC256V FRAM I2C example...
Hi,
We are nearing production stage of our project, and are looking at programming on a large scale. Using the nRF9160 we need to program the latest modem firmware along...
I have a broadcaster and a central device. The broadcaster beacons data every 60sec and goes to sleep, a configuration I have considered for minimal power consumption. Now...
During tests with a "User controlled PLMN selector with Access Technology '6F60'" one device stuck in a curious state:
nRF9160 SICA B0A mfw v1.3.3 CAT-M1, PSM: PTAU 24h...
Hi Nordic community:
Can we configure nRF52840 to support a 1.3 V VIO?
I see from the datasheet, after the internal regulator, what supplies to the chip is actually...
Getting an error from mcumgr and I'm not sure where I should start debugging this.
My environment:
nRF Connect version 2.1.0 Board: nrf52840 DK and nrf52832 DK Host: MacOS...
Hello,
I'm developing with nRF5280-DK, using Zephyr-OS with mbedtls for the cryptography, and I need to have DES and 3DES enabled by default.
I tried to set in the prj...
