Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
Hi,
We have to enable the radio shorts in our developing multi link firmware. ( We let any node connect to 3 other nodes at the max ( 1 as a slave and 2 as a master )) ...
Hi all,
I use GPIOTE and DPPI to read SPI data from IMU sensor. After IMU send out "Data Ready" signal, GPIOTE will be triggered and DPPI start to read using SPIM2.
And...
Hello ,
I am working on a project an nRF52840 + quectel BG96 modem. I am porting the freeRTOS cellular interface library for the Nordic platform and mainly the FreeRTOS...
Dear all,
I am developing a device that base on nrf52833, nrf connect sdk ver 2.0.0
The device run bluetooth mesh. And becase it was powered by battery, so it must go...
Hi there,
There are some problems when setting nrf52840 GPIO interrupt. When I use gpio_pin_interrupt_configure_dt api to configure 11 gpio pins then download to my customer...
Hi
I am testing <InstallFolder>\examples\peripheral\usbd_cdc_acm project, when I use serial tool of pc to open port, it can send or receive data.
but if I don't want to...
I wrote this function:
When calling it and
ptr points to something odd, the chip seems to crash. Can you not dereference odd memory addresses?
Or is there a different...
Hi,
I have been using nrf5340 audio dk fir the last couple weeks with nRF Connect SDK v2.1.0 and nRF Connect SDK v2.1.1. There were issues with the audio template for walkie...
Hi,
I'm using nRF Connect 2.1.1
I create a application based on 802154_phy_test template.
When I create a configuration and build for the nRF52840 it compiles OK.
...
Hello,
I have a TMP117 attached to I2C1 on a nrf5340 and am using the zephyr NCS v2.0.0 driver to communicate with it.
How can I configure I2C1 for power management...
Hi, I am looking to use mcuboot to manage 2 separate images. The idea is that under certain conditions, image 1 would jump to image 2.
To test the idea, I am using the zephyr...
When using the Toolchain Manager through the nRF Connect for Desktop app, the Toolchain Manager is failing to fetch the index files resulting in the version 2 toolchains being...
Hi there,
as already mentioned in other tickets I'm developing a usb to uart bridge based on the nrf52820. The nRF5 SDK version I'm using is 17.1.0.
Right now I'm facing...
