I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Tagging Ø yving !
Hello everyone and thanks to the Nordic team for a nice day in Stockholm.
Since the single cell tower localisation was very good compared to GPS...
Hello everyone,
I'm using Gateway (serial example) and send packet "Heartbeat Get" to Devices (Light Switch Server Example )to check alive of devices. But when check alive...
What API could be used to send out ZDO Device announce, when router (zr) or end device joins network ?
Is there any sample code could be referenced?
Thanks,
Robert
Hi!
Three or four months ago I create a ble mesh with 6 nrf52840 Dongles. Now I want to reset all Dongles in order to create a new ble mesh with a different functionnality...
I changed seqValues variable of the following function from 0x8000 to 0x0010. But I can't see LED light darkening. How to dim LED lights by nRF52832 PWM?
static void _ledPwmConfig...
Hello,
I just observed some strange/interesting behaviour. On one of our products there is a green LED connected to Pin 3 of GPIO port 0 on the nRF5340. When I connect the...
Hi everyone, I'm developing a program with the NCS 1.8 using NRF52840 and I want to use the SPI, the fact is that I've to connect my device to those pins
And as you can...
I am using s112_nrf52_7.2.0_softdevice with nRF5_ SDK_17.1.0 and Segger Embedded studio for nRF52805.
My application code uses 150 kb Flash(Out 192 kb) . I want to develop...
Hello, I have a question regarding to the DTM;
Is there a way to count the number of test packet transmissions or set the number of test packet transmissions in the direct...
Hi,
We are using the latest ncs release (2.0.2) on a nRF52840 integrating Matter. When looking at the sample apps (e.g. light switch example), the RAM usage for the Matter...
I would like to using nRF52832 EasyDMA for reading and writing to and from the RAM for peripherals (E.g.NOR flash, Analog front-end (AFE), etc.). Could you suggestion example...
Hi,
Greetings!
We are trying to understand how we can send battery voltage to mobile application from nRF52832 based battery operated device.
Please note that we are...
I have tried to connect my NRF 5340 board with BLE application the last few days but had no success. I already tried other solutions like disabling the MSD via the J-Link...
