Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
Hi,
I use the modified version of the USBD example(nRF5_SDK_17.1.0_ddde560\examples\peripheral\usbd) in nRF5 SDK from here . (My development kit is nRF52840DK.)
And I...
Hi, I have configured normal uart, where you send 1 tx_buf and wait for the rx_buf until you get a response. This setup was fine until the logging feature was requested. However...
Hi, I am developing a product using BLE with nrf52832. We are aiming for a BLE communication range of around 1.0m. However, if txpower is set to -20dbm, BLE communication...
Hi,
I found this forum post about the Verizon APN:
https://devzone.nordicsemi.com/f/nordic-q-a/46288/nrf9160-verizon-sim
This implies that I don't have to use "AT...
I want to parse the following JSON { "ver": 3, "mode": "online", "custom": { "apl1": [ "off" ] } }
Tell me about how to parse json and how to write code
The keywords...
Hi Everyone,
I am developing a PC App. with nrf52840 usb dongle (central) to communicate with nrf52840 BLE device (peripheral) on long term and transport data. Everything...
Hi,
I was working on nrf52840 DK and I left it a few weeks and came back to use it and I discovered that the whole USB connector (J2) got removed. Not sure if there are...
To the kind attention of Nordic support team,
I'd like to know what would be the best theoretically way, if possible, to control "when" multiple notifications are sent...
Hi,
I am developing with the nRF52833 DK using NCS v2.00.
I have edited the existing TX power service (TPS) to allow the client to set a desired TX power. I have added...
I'm using the nRF52840 with NCS SDK 2.0.2 and need to be able to change the BLE advertisement name of the peripheral device dynamically.
I have this working when using ...
Hello Devzone,
I am building firmware for an nRF9160 based device, starting with an ncs 1.6.1 sample app and LTE modem firmware v1.3.1. I'm in North America, and when testing...
I am using the SD card driver from nRF5 SDK v17.0.2. Device nrf52840, IDE Segger, Custom PCB. nRF52 DK as progremmer.
There are problems when deinitializing the SD card...
Hi,
I am developing a peripheral in ble, and I receive the following error when I disconnect a new connection within the connection callback.
bt_conn_disconnect ( conn...
Hi,
I'm writing an application which, depending on configuration, will either use ESB and Bluetooth, or just ESB.
I read through the article ( ) describing how to use...
