Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi, this is my setup:
nRF52840 Dongle configured to run as a peripheral BAS.
The BLE desktop app was used to configure the dongle.
I know that the dongle is working...
I was wondering how one might get the nRF9160 to enter the low power modes when making my own firmware? If possible could someone point me in the direction of an implementation...
We are building a gadget which senses temperature and humidity level using nrf5340 and using i2c as interface. We are using a slave which has SHT3X sensor for reading the...
I've been trying to use the NVS subsystem along with BLE and FOTA.
I got BLE and NVS working fine.
But if I enable FOTA (just including the code, not running an update...
I'm having trouble with a computer that can't run a Python script, which is using the library pc_ble_driver_py
I'm confused about the answer posted in
I've tried downloading...
Hi!
For a custom project, I need to enable and disable soft device for power consumption optimization. I've followed ble_app_gzll to enable and disable soft device. Unfortunately...
Hello,
I'm using the nRF52840 DK, SDK 17.1.0 and SoftDevice S140. My project is based on the Blinky peripheral example. The problem is the following:
Basically, turning...
I see a lot of threads about how you need to disable the UART while you're not using it because it has a couple of milliamps power consumption.
However, most of those threads...
Hello Team,
We are in process of designing our product with nRF52833. To secure our product and possible Firmware readouts, we are planning to use the APPROTECT feature...
So, I'm working on a project with two RGB LEDs, that's going to be powered by a coin cell. The device is going to spend most of it's time asleep, only waking up for a minute...
Hello - The nRF Connect for VS Code extensions updated today and it appears to have broken then nRF Terminal connection monitoring.
Old Behavior
Connect to device...
Hi,
I have a nRF52840-DK which comes with an o n-board SEGGER J-Link debugger/programmer to use with the internal microcontroller or an external one.
Also, I bought a...
Hello Sir/Madam,
I'm using Nrf52833 for ble_uart + saadc but this device given only 2 meter distance range .I want to increase that distance range.
How to increase distance...
Hi
I want to communicate with nRF52BK (nRF52832) board via its UART.
Eventual goal: Get Android device, acting as USB host, to connect with nRF52DK board's UART Short...
