Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
The problem i having seems to be tricky and i spent hours trying to figure out whats happening. So, i will try to put all details possible. Im two days with this issue and...
Hi there,
I faced this issue while I was setting up a test through two UART0 & UART1 ports on NRF5340 chip, using baudrate 1000,000.
Here is the setup:
UART0 &...
I currently use nrfConnect on android to download firmware to nrf52832s. I am just getting started with nRFUtil and the dongle.
If I understand correctly, I should be able...
I have a nRF52 DK from DigiKey that I've been evaluating and I ran into an issue: I had a custom app that was talking through Bluetooth and sharing some custom characteristics...
Hi, I'm using NXP LM75B temprature sensor based on nRF SDK's example code.
I would like to save power on this sensor.
I have prepared the code as follows:
Following...
Hi! Could you clarify a bit about Bluetooth mesh gateways' implementations. I wonder to know possible ways of Bluetooth mesh gateway implementations. How is it possible right...
I'm developing for nRF52832, SDK 17.0.2 and softdevice S312 7.0.1.
After I upgraded from Segger Embedded Studio 6.22a to 6.30 I found that turning on any compiler optimisation...
HI DevTeam,
I'm using the nRF52840 as co-processor due to the semiconductor shortage and I don't need to use the RF section. What should be done with the antenna pin in...
This is the implemenatation spec for GATT server database (reader) firmware i am working on.
I have implemented advertisement packet using nRF Connect SDK latest.
Not...
Hello,
I am customizing the BLE DFU bootloader for nrf52820. Integrated an LCD to it.
Now I need to display the percentage of firmware download on the LCD. It will take...
Hello everyone,
I am working with the SDK v17.1.0 with the DK nRF52832. I want te retrieve data from a battery cell monitor which uses the LTC6804 from Analog Device.
...
Hi,
I need to capture time in nanosecs between 2 tasks, for which I am using the zephyr suggested time measurement code as in:
When I am trying to compile the above...
Dear DevZone,
our goal is to replace the RX side of an old system, which is using the nRF2401. For real-time capabilities, the Shockburst protocol was employed.
Reading...
Hello, Nordic Engineer
I use nrf52811 and SDK 15.3.0
In example 《ble_app_uart》, I added timeslot（ESB）
Run this code《nrf_esb_write_payload(&tx_command);》
Subsequent...
