Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
SDK: 15.3.0 Example: ble_app_multirole_lesc DeviceA: EYSHJNZWZ (nRF52832)
I want to know the relationship between API and events. Take "sd_ble_gattc_characteristics_discover...
Hi nRF Support,
I get nRF5 SDK version 17.0.2 and learn Peer Manager handler implementation (pm_handler_flash_clean function). Lets consider this case:
- 2 bonded peers...
My thingy:91 does not connect to the LTE network. However it does detect the Swisscom network (Switzerland) and shows it as available.
I did:
update the modem with mfwnrf9160123...
Hello, I am trying to program the peripheral uart sample on to my Thingy 91 using the nRF9160dk and 10 pin connector. I am able to successfully build and download the target...
I hope I am posting this in the right place but I am looking into learning more about developing devices that use Bluetooth. I have been looking into getting a dev board but...
Hello All,
I am working on nRF52840 DV-kit, using SDK - nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71
I am trying to create .c and .h file in my project for gpio_configuration...
Hi,
I have layout a borad with nRF52810 and use IO to control other ICs.IOs map as blow.
#define LSM_6DS_SPI_CLK_PIN 9 /**< SPI */ #define LSM_6DS_SPI_CS_PIN 4 #define...
We are using nRF52840 chip for our development and till now we have used nRF SDK's zigbee CLI example for development.
Now we are interested in nRF5340 chip but I have not...
hi，
iI'm newer useing nRF5340， nRF5340 two cores communicate via IPC ,then exchange data through which path that is IPC or CTM ，What's the difference between IPC and CTM...
Hi,
I am powering the NRF52840 in normal mode by supplying 1.8v to VDD with VDDH and VDD shorted.
In order to use USB the VBUS pin is connected to the USB VBUS line. ...
Hi,
I am programming the PCA10040 board (tested 2 different boards) with the ram retention example program from the latest SDK (NR5 17.0.2). With this example is supposed...
Hi :
We create UART Over BLE service on NRF52832 SoC. It worked fine used SoftDevice V2.0.
Now update SoftDevice to V7.2.0. got this issue. where can i found SoftDevice...
I'm trying to drive the RGB LED light on the Thingy:91. So far, I've not been successful. I was hoping that by listing the steps I perform I might be able to get some advice...
Hi,rotocol
In Nordic's Smart Remote 3, it is mentioned that IR transmitter is protocol agnostics while IR driver is Protocol specific. Is it possible to write a common IR...
Hi,
Is there any battery life calculations for NRF52 and NRF51 (Beacon)?
For example: if TX power of NRF52 is 0 dBm and it broadcast every 5 seconds ? Or with any other...
