The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm attempting to use the pc-ble-driver-py on Windows 10.
I successfully installed pc-ble-driver-py-0.11.4 using pip but when I go to run a Python script using it I get...
Hello,
I am looking at the ble_app_hids_keyboard example in SDK v17.0.2. Where can I find a table that will convert the letters on the keyboard to the hex values used in...
I have a Python script that I am wanting to use to flash our devices at manufacturing that uses pynrfjprog.
When running the script on Windows I get this error:
"FileNotFoundError...
Hi,
We have been working with a Zigbee coordinator, router and an end device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b, Softdevice and FreeRTOS...
Hi nRF support team, By using the nRF Connect SDK, I am trying to implement an SPI communication with the display module from my nRF52840 dev kit and nRF52840 as a master...
Hi,
we have the need to implement the border router functionality for 6loWPAN in our device using a nRF52840.
Essentially we need to replace the Raspberry Pi in your examples...
Hi, everyone,
I'm trying to assign an SPI End Event to a DPPI channel on nRF5340dk to trigger a counter automatically. However, the value of the counter never increases...
Hi, I am writing a coordinator application based on the zigbee CLI example. I am using SDK for Thread and Zigbee v4.1 (latest if I am right). nRF52840 DK as HW. I want to...
I need to collect data from approximately 20000 points. I want to form a BLE mesh network and collect the data. The sensors may be buried below the ground level about 30 to...
Hi all,
I have a problem with nRF52840 acting as TWI slave. I'm using TWIS. Typical scenario is:
1. Master writes request and ends transaction using stop condition.
...
Hi,
Scenario: 1 Thingy52 device and nRF52 Development kit is in a mesh network, where Development kit is connected to PC via usb cable and also connected to J-Link application...
With the release of SDK For Mesh v5.0.0 the mesh_stack_power_down() was introduced.
When calling mesh_stack_power_down() an assert was hit in nrf_mesh_timer_tail_handle...
Hi
I am using Mesh SDK v4.2.0 and I want to add Simple_On_Off Model to the Light_Switch example and provision and configure it with the provisioner example.
So far I have...
