I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi
I have 1 PCA10040 dev kit and 1 Raspberry Pi 3.
If I connect NRF dongle to Raspberry Pi will Raspberry Pi act as mesh-node ?
All I want to do is send data from PCA10040...
Hello,
nRF52840 is having the inbulit RTC for keeping the time.
Should i need to use external RTC with coin battery for even after power off the BLE nRF52840.
PLease...
Hi!
We're considering implementing some security measurements into our devices, and so naturally we've started to investigate CryptoCell and other Backends supported by...
Hello,
I recently updated nRF Connect to version 3.4.0 (Bluetooth Low Energy). I'm observing, that the tool is not able to reconnect to a peripheral that was previous bonded...
Hi Nordic Experts,
I use nRF52832 for a custom board, I use GPIO P0.17 and P0.18 for controlling NMOS switch, for buzzer and vibration motor, and the frequency is controlled...
So I seem to be having trouble interfacing with nrfl2401. To initially test the chip, I sent `0xFF` to be able to read off the status register but when I do, I get `0x1C`...
Hello Nordic Team,
We are working on a BLE project with RSL10 board from OnSemi. We need a BLE sniffer to capture and analyze the BLE packets in the air for debugging purposes...
I have a module LAIRD BL651 based on nRF52810 SoC
I’m using the latest nRF5_SDK_16.0.0
I can flash ...\examples\ble_peripheral\ble_app_uart\hex\ble_app_uart_pca10040e_s112...
By taking CLI as reference: added end point handlers, changed flash placement file with zb_ep_handlers.
Issue facing was:
ZB_ZCL_CMD_REPORT_ATTRIB command is not at all...
Hi,
I have nrf52840 with softdevice and i want to write 12 byte of data at a time in internal flash,suppose i write 50 records and i have to also read it these data from...
Hi.
I am familiar with Nordic NRF51 and NRF52 as I developed OpenSource firmware for chinese ebike displays with them and using the provided examples for UART Bluetooth...
Hi,
I am trying to understand the different PHY modes available in nrf52840. What are the differences between nRF 1Mbit and 2Mbit proprietary modes when compared to BLE...
Hi,
I use nRF51822 powered by CR2032 battery. Same decoupling as dev board PCA10001.
Would you recommend different values of decoupling capacitors for battery powered...
I have SPIM working at 8MHz on nRF5340-PDK
I want to increase the SPIM speed to 16MHz.
The errata for nRF5340 states "In 128 MHz mode, SPIM max receive frequency is 16...
