I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
I have to write this page in case of the application firmware update, so I have to unprotect it in the bootloader (in the nrf_bootloader_app_start_final() function). won't...
We've been hunting down an issue there when we call nrf_drv_uart_uninit() we get a high static current which indicates that a clock or peripheral is being left on.
After...
I am getting the error:
There was an error adding your device: No device found with id 'nrf-352656100878829'. Verify you are passing a valid device id and not a device name...
Hello there
I am now using Nordic 52840 dongle hardware ready to be used as a zigbee sniffer, and I have seen that official documentation is feasible.
My current environment...
I am having trouble modifying simple_hal.c from the mesh SDK v4.1 when buttons are on Port1 instead of Port0 on a nRF52840. I have buttons on P1.01 and P1.02.
Everything...
We're attempting to move from v1.1.0 to v1.2.0 of the NCS, in order to take advantage of some driver improvements (particularly DPD in the SPI NOR driver. When we migrate...
Hi,
I am currently working on a custom product that uses module BMD-300 from u-blox, which has nrf52382 chip in it. My application works fine and now I want to integrate...
hi,
Im developing a mesh network based on the nRF52832. I want to send some long message(over 11 byte) without segment, so I enabled the EXPERIMENTAL_INSTABURST_ENABLED...
I turn on the Instaburst feature already , after that , I program serial example to 2 nRF52832 and run it with interactive_pyaci
when i try to do PacketSend with 20 bytes...
I am running a Bme280 sensor with nrf9160 and getting this error msg ( [ 1;31m<err> i2c_nrfx_twim: Error 195952641 occurred for message 0 ) while getting the actual sensor...
Hi All,
Since I measured a very current consumption by testing CLI example (ftd/usb) I'd like to know how to switch my nRF52840 DK as Sleepy End Device.
Any suggestion...
I have a zephyr sample app running on a nrf51822. It's the onoff_level_lighting_vnd_app found in samples/boards/nrf/mesh. I have an iPhone running nrfMesh. I can't find documentation...
Hello, Im working with nrf52832 and sdk15 I'm working with the example: nRF5_SDK_15.0.0_a53641a/examples/ble_central_and_peripheral/experimental/ble_app_hrs_rscs_relay I want...
How can I receive all the packets from all addresses?
In the datasheet I see there's an RXADDRESS which setups the receiver to which address it will listen to. I want to...
I am using the zigbee sdk4.10 cli_agent_router and multi_sensor example. The 52840 module is E73-2G4M08S1C, antenna is a built-in ceramic antenna. During operation, the communication...
