Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
nRF52832, SDK15, s132
When I have event PM_EVT_BONDED_PEER_CONNECTED, should I call
for secure connection? Or it secure connect will call automaticly from SD? Because...
Application Summary: My application is a mesh node that also implements a BLE central (to periodically connect to a BLE peripheral) and acts as a mesh relay with custom mesh...
Hello,
I'm trying to get an idea of the level of security provided by various security features described in the nRF52840 specification and several of the application notes...
Hi!
I'm currently setting up the nRF9160 dev kit for development and are having some trouble with "building" the asset tracking application.
Building ‘zephyr/include...
Hi All,
I am doing a Mesh development project with nRF52840 and a custom board. SDK version: nrf5SDKforMeshv320 Testing Example: light_switch
I had changed the port/pin...
The goal is that we can update the firmware version with the smartphone or tablet without having
need to go through the development tools
(cable, IDE, ...)
if so, how can...
Hi,
In our firmware we're writing the entire contents of our UPDATE.BIN file successfully with flash_img_buffered_write's, but after boot_request_upgrade and a sys_reboot...
When my Nordic device is running my custom BLE application I notice that the device address is 0xC4318DBD687C. When device is running the bootloader service the device address...
Hi Nordic,
As far as I can see, there is BLE_NUS_CONFIG_LOG_ENABLED defined for ble_nus in sdk_config.h. However, I cannot find the similar BLE_NUS_C_CONFIG_LOG_ENABLED...
Hi, can we use a manufacturer name of our own for the usb in nrf52840?
We know that we can still use the Nordic Semiconductor's usb vendor in a commercial product.
Best...
Hi, Can I use nRF24LE1-F16Q24-DK without nRFgo Starter Kit? If yes please suggest me programmer to program nRF24LE1 by Keil IDE. by referring documentation I found its support...
Hi
SDK v15.2.0 SD 6.1.1
I have managed to send out "Connectable, Non-Scannable" extended adverts with some AD packets as payload. On a frontline sniffer as per the file...
I am developing a HID keyboard based on an nRF51822.
The firmware source available here:
https://github.com/martonmiklos/ble_keyboard_fw
(It is based on the ble_sdk_app_hids_mouse...
Hello,
i'am trying to control the pwm Idle State Level.
between my Sequence's (1sek) the PIN stays High But i need it low.
I try to set the GPIO Out Register, but...
