Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Im streaming audio from a gateway to headsets using BIS, but I am unable to get multiple streams working, so that I can switch between streams on the headsets. How do I set...
Dear,
We are using the nRF52840 with a proprietary protocol.
We plan to use the nRF52840 to sniff/poll RSSI on different (5/6) channels on periodic time (typ ~100 us)...
Hello, I have a problem on getting the dynamic tx power to work properly on the BL5340 using the hci_pwr_ctrl. I tried the example, it build and flash correctly, no error...
hi!
I get the message "The build configuration is stale. Run a pristine build" even after rebuilding in all versions of nrf connect for vs code after 2023.7.129.
I have...
I'm developing a product with the nRF52840, using Zephyr (Toolchain & SDK version 2.7.0). Is there a way to set up two PWM outputs having the same frequency and duty cycle...
Hi,
I am working on implementing an I2C node in my nRF52840 based sensor. However I am getting the following kernel panic.
I removed all I2C node related code that I...
Hi,
I'm developing a new battery powered sensor device with an NRF52840 and have some thoughts about efficient power supply. The main question is: Using an external DC...
Hi,
I have opened Sample "Peripheral_hr_coded" and added build configuration.
Then I clicked on Action --> Build.
Please validate below log. Is it proper ?
Log is...
Is it possible to dynamically switch between USB CDC (Communications Device Class) mode and USB MSC (Mass Storage Class) mode on the nRF52840? If so, could you outline the...
Hi, recently I started migrating my company's firmware from nRF5 SDK to nRF Connect SDK. I have been following the devAcademy courses and so far 1. I have created my custom...
Hello, guys.
We need USB CDC ACM and UART driver with DMA to run in parallel as two different nodes in the device tree.
For that purpose, here is what we have in the prj...
This is a general question about selling our modem-enhanced products internationally. We use an NRF9160 (NB-IoT), but we have some of our devices equipped with older Telit...
Hello,
NAS-RAI (Non-Access Stratum RAI) used on NB-IoT Control Plane : on nRF9160 it was controllable via the AT%XRAI command, using the <rai> parameter :
0 – Undefined...
SOC: NRF52840
SDK : NRF conenct SDK 9.11
Application Gateway
we had end devices to join the network which is whitelisted in the coordinator ; so please can you let...
aliexpress.com/.../1005007557383132.html
I bought the above board I checked the revision information with nrjfprog --deviceversion and it was revision 1 All functions including...
