Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
Hi,
I used the reference code from inter_less8_exer3_solution and successfully built it with the nrf5340dk board. However, when building it for the nrf7002dk , I encountered...
I'm using firmware 1.3.6 and sdk 2.7 for Nordic nRF9160. For the internet connection ppp is being used.
Here are the results:
modem shell:
time wget https://leil.de...
Hi,
as i would like to use the uart shell for production purposes as well (e.g. setting the devices serial number) - how can i turn off the shell at runtime (in order to...
Hi,
I've been working on building and flashing the OpenThread CLI sample in two setups:
Setup 1 : nRF21540DK
Setup 2 : nRF52840DK + nRF21540EK
While I've managed...
I've been working on building and flashing the OpenThread CLI sample in two setups:
Setup 1 : nRF21540DK
Setup 2 : nRF52840DK + nRF21540EK
I'm using NCS v2.6.1....
Is it possible for the nRF7002 to operate in both SoftAP and STA modes simultaneously?
From my understanding of the nrfwifi driver, it seems that this functionality may...
Hello
I'm working with the nRF21540 and the nRF Connect SDK 2.6.2.
I would like to set my TX Power to 20 dBm and also check this value. Currently my configuration looks...
Greetings,
I've been developing a DFU firmware that should update the device through Android. The thing is, the device works, but I changed the advertising name, and it...
Hi,
I'm using the nRF5340 Audio application under NCS v2.5.0 as Unicast client.
I want to use the GATT Caching feature on my application.
How should I implement it...
Hello.
There was a problem with high current consumption when using Antenna 2 in some products.
The failure rate seems to be less than 7%, and the current consumption...
Hello,
I want to combine BLE, ANT+ and Apple Find My in one project.
I have permission to use ANT+ and Apple Find My.
I ran the two examples separately and they worked...
I have noticed that the RESETREAS register does not accumulate flags even though the documentation says it should. " Unless cleared, the RESETREAS register will be cumulative...
I have recently purchased a nrf7002 EK from element14.
I have connected it to nrf5340DK board and tried flashing the Wifi-shell sample application(with the help of video...
I’m not sure if I’m posting in the right forum, but since the EVK-ANNA-B402 uses the nRF52833, I thought this might be the place for questions related to it.
Steps followed...
I am using the cdc_acm example and have added a command to set and read tx power. I am trying to use the following commands for this.
BT_HCI_OP_VS_WRITE_TX_POWER_LEVEL...
