I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi Fellow NCS-ers, I understand that the configuration setting CONFIG_BT_EXT_ADV, CONFIG_BT_CTLR_SCAN_REQ_NOTIFY, and bt_le_ext_adv_create() with the appropriate callback...
I am using nrf sdk v2.4.0 and I wanted to disable TFM so I added the following definition in prj.conf.
CONFIG_NRF_SECURITY =n
CONFIG_BUILD_WITH_TFM =n
But my program...
A problem is experienced with our nRF52840 device, which occasionally stops working and cannot be reset.
Below are the issues observed:
The main software is stopped...
I am working on the broadcast_audio_source example, trying to access audio from the I2S microphone. However, I do not have much experience with Zephyr. The example is mostly...
The thread where it happens is "unknown” despite the fact I name all the threads I create. With addr2line I found that it is zephyr/kernel/timeout.c 56 but it says nothing...
Dear all,
I'm designing a circuit that should allow powering the nRF52840 board with either an USB power supply (USB2) or a (non-rechargeable) CR2032 battery (B1). According...
Hello.
I encountered the following problem. I have an nRF52840 microcontroller that is already soldered onto the PCB board. It doesn't have any bootloader. As an example...
Hi,
We have an nRF9161DK and received our own custom boards this week. When we tried to program our custom board, the development kit disconnected from the computer and...
Hi all!
I'm in the process of trying to put together an nb-iot app on Android studios that would communicate with data from the Thingy 91 board. I've been trying to go through...
Hello everyone,
I've been working on testing PPP support in SLM 2.6.1 without cmux on my Linux host machine. However, I encountered some logs during the process: Note: For...
Environment:
I can't seem to get the one button sample to do anything... I get a steady ~1sec flash from HOST led on the npm1300, but I get nothing from pushing SHPHLD...
I have an EC11 rotary encoder wired to my nRF52840 and I am trying to get readings from it using the sensor API. However, I'm having issues with (seemingly) garbage data....
Good day. We ended up getting a bootloader based on the NRF5 using the Serial Recovery method and a non-upgradable bootloader. The update is coming from a microcontroller...
I'm working on a linux driver for nRF7002 based on the experimental linux driver: https://github.com/NordicPlayground/nrf70-linux-driver . This is being done on linux 5.13...
Is it possible to somehow set a lower charge current than 32mA for the whole charge cycle or force trickle charging for the constant current charge cycle? The issue is that...
