Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
Hello,
I'm having an error when running the spi_flash example on a nrf5340DK.
I added this to the .conf file to have more info:
Here are the console logs:
I'm...
Hello,
I am running into an issue when I try to use two SPI controllers simultaneously on the nrf5340dk. I am using ncs v2.6.0.
What I am trying to achieve, is a system...
Hi,
I am working on a device that is keyboard like, but it just needs to send one cmd to switch the screen - alt+tab/cmd+tab. I was able to get this working with Windows...
Hello,
Which nRF connect for Desktop should support Windows 7 OS?
The last one that supports Windows 7 cannot download the PowerProfiler addon.
For development we...
When I changed SDK v2.2.0 to v2.6.0 we are facing this issue can u provide information regarding this.
I have enabled necessary configuration in prj.conf file
# Enable...
I have my application code which builds and runs on my nrf5340DK. The project files were based on the zephyr sample for multi-advertising BLE.
Right now I'm building the...
Looking at the product specification for nRF5340, I can see power consumption data for the I2S interface.
https://docs.nordicsemi.com/bundle/ps_nrf5340/page/chapters/current_consumption...
Today I am attempting to set up an MQTT connection from a Thread device to an MQTT server on the Internet (for better or for worse, if this is a terrible idea I'm open to...
Hey
Im trying to as low power consumption as possible and for that i have found that sys_poweroff() gives me that.
My problem is that i cannot get a pin state change...
I work on a project where we make a device with a 9160, and our application is build using NCS 1.7.0 and is programmed with MFW 1.3.0. The network our devices connect to is...
I have basically all my code disabled, all I do in main() is get a pointer to the "zephyr_console", suspend it and return.
This gives me an average power consumption of...
Hello,
I try to dfu with mcumgr but I feel like the download speed is a little slow. So I want to increase download speed. I think that mcumgr has the command to set boudrate...
Hello,
We are designing a board with a nrf5340 with a VDD of 1.8V.
The board is very small and it's complex to fit all the components on it.
We are thinking of removing...
Hello,
I was wondering if there is away to perform DFU using SPI without smp protocol or mcumgr from one nRF52840 to another? What I am trying to do is to send a firmware...
