The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi:
I set up a fresh install of the NRF Connect Extension Pack in VS Code on my MacBook Air M4 and was able to build and flash the Blinky demo to my nRF52840DK. The issue...
Hello, this ticket addresses three issues:
1. After installing nrfutil with subcommands device and toolchain-manager and sdk-manager, into %USERPROFILE%\.nrfutil, everything...
Hello,
Since our Product Launch we have gotten feedback that pairing with some (but not all) Apple devices is a significant problem. Even through several attempted fixes...
After upgrading nRF Connect SDK from 3.1.1 to 3.2.1, our fixed regulator stopped working. We are on nRF54L15. Tracking it down further, this seems to be some sort of GPIO...
Hi,
I am porting a product from SDK 15 to SDK 17 and to Nrf Connect.
We need to maintain code combability as far as possible between products using SDK 15/17 and products...
I'm creating a system test for manufactured units and if it's OK I would like to set a permanent flag in an area that will not be erased if I erase flash at a firmware update...
nrf sdk 17.1 example:peripheral/uart/pca10040 I attempted to use P0.9 and P0.10 on the development board to set up a UART serial port for data transmission and reception ...
Hi,
I am on NCS 2.9.0, I have tested lesson 5 exercice from NRF Intermediate course about BLE DFU, I have some questions about it:
- with mcumger, is there a way to update...
Hello,
We have a custom board we are developing on that uses the nRF54L15 MCU. The board has some LEDs that we were hoping to drive using PWM, but these are connected to...
Hi all
I have some trouble with a new batch of nRF9151 chips.
The old one had the Firmware: 2.0.2
The new ons have the Fimrware 2.3.5.
My application does no longer...
Hello
I tried to test OTA function with smp_svr example.
I want to use the external flash mx25r64 on nrf54l15-dk(v0.9.3) to store update Firmware over BLE. SDK version...
Hello,
I have some unclarities for the APPROTECT mechanism on NRF9151.
Basically, I had a misunderstanding of the involved CONFIG features, and as a result I used CONFIG_NRF_APPROTECT_LOCK...
Hello,
I’m using an external NFC reader/controller (NXP PN7160A1HN/C100E) connected via I2C to an nRF52840 module (Raytac MDBT50Q-1MV2) on a custom PCB. (Programming is...
On nRF52840, after power up, I continue to randomly get hangs. I am having trouble figuring it out, but it seems every time I encounter the issue, it is related to RNG. If...
We are designing BLE products based on the Nordic nRF52840 chipset and star network topology which are used indoors, according to the network structure, we use one Master...
