nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Hi there,
We are doing some testing on an eSIM with the nrf9160 DK, and we are looking for an AT command that can be used to read the eUICC ID of the SIM. We are using the...
Hello,
We are planning to integrate the LwM2M carrier library. Our system uses mfw 1.3.3 and NCS 2.1.0.
Based on the following page https://infocenter.nordicsemi.com/index...
I'm trying to update MCUboot from the application. As a first test, I enabled the flash shell commands. I can erase somewhere within the flash without problems:
uart:~$...
Hi,
I have a simple SPI circuit to read data from a flash memory W25Q64 to be exact and I have difficult time reading the device address of the chip through SPI.
The situation...
Hi Devzone,
we are working on nrf5340 mcu, from the DTM sample, l learned that the application run on network core only, but my application scenario is combine the DTM with...
Hello,
I'm using the SAADC voltage conversion formula from the Nordic example as follows: 10 bits are used in the example.
By the way I want to change ADC resolution...
This is a follow-up to my previous post . I'm developing a BLE Peripheral application on the nRF52832 that uses NRF_SDH_DISPATCH_MODEL_APPSH to receive events from the SoftDevice...
I think this is a bug report for the VScode plugin
One of my boards shows this error when I try to debug
Nrf52833 custom board connected with SWD on Jlink
I was...
Hey there ,
I am trying to modify the Nordic Radio Test example from the pack installer in Keil
for some reason I am getting "
Resource Not Found
We're sorry,...
hi team,
i am using nrf52840 controller and sdk 16.0 i want to know difference between twi and twim and twis driver apis in infocenter.which one i have to use once i connect...
I am trying to display the p_data received data using below inside NRF_BLE_SCAN_EVT_NOT_FOUND case but I am receiving the below data.
2| 1 |6|1a| ff |4c|0|2|15|ff|ff|0|0...
I am working on direction finding connectionless locator/beacon(AOD). We designed beacon board with nrf52811(build option is nrf52840 DK nrf52811) and antenna array, use a...
Hi Everyone,
I recently updated from SDK 1.8.0 to 2.2.0. With 1.8.0, I configured the nRF9160 MAGPIO and COEX0 in my Kconfig file. But with 2.2.0, I don't see that in the...
Hi,
In SDK2.0.0 version, can the TX_EN timing of nRF21540 be changed through SPI control?
If the timing of TX_EN can be changed through SPI control, how FW implements...
Hi,
The example that I use is from here .
I have to use the USB interface to send and receive data between the host PC and the nRF52840 chip.
In the example, I can only...
