Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hello everyone,
I'm working on an Adafruit Itsybitsy nRF52840 Express board and I'm trying to flash the SoC with a J-link EDU mini. I use the nRF Connect extension on VS...
Hi,
I currently do some advertising tests with Nordic's nRF52840-DK and Zephyr. I have one board doing extended advertisements, one transmission every second. By means of...
Hi,
We are using nRF52820 right now and we would like to decrease the current of advertising, I have set the "init.config.ble_adv_slow_interval" to ''1024'' and the average...
ref. an earlier ticket,
I am using ncs 2.0.0 on a custom nRF52840 board
When enabling the CAF BLE state module, I get a build assert error due to
BUILD_ASSERT(!IS_ENABLED...
OpenThread daemon fails to run whenever using the nRF 52840 DK development board but works fine when using the nRF 52840 Dongle. I reinstalled it multiple times and started...
I would like to test he Wi-Fi Provisioning Service sample ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/wifi/provisioning/sample_description.html...
Hi guys,
for a current project, we need access to the local Zigbee binding table of the device (getting information about the binding of the current device).
I've spend...
Hi Nordic,
When I was using NRF52840 for FCC certification, the DTM 8dBm, 2Mbps sideband emission power exceeded the standard.
The antenna matching circuit is to use the...
Hello All,
I am using nrf9160 based custom board with external flash. I am trying to build an application with mcuboot, primary image in internal flash and secondary image...
I am developing with nrf52832 (s132 v7.0.1, SDK v17.0.0) as a peripheral device.
I am communicating with an Android device (SH-M05) as central.
There are times when I...
Hello,
We are developing a device that uses only NUS (Nordic UART Service) and DFU from the services. In this case, is it possible to implement Pair/Bonded with a client...
Hi,
I am currently trying to get the USB CDC ACM Example on the nRF52 DK to work using the SDK v14.1.0 . But for some reason I can only send/receive data using PuTTY but...
I found this post devzone.nordicsemi.com/.../zephyr-central-to-peripheral-communication , which was helpful to understand the overall structure of both central_uart and central_hr...
I'm trying to build the UART app with SES as per this example:
And I'm getting this error in SES:
Did I miss a step in the installation and setup somewhere?
Dear Support team
1) I find that there is a C9 in the nRF52840 reference circuitry for CKAA WLCSP which said that the C9 is not required for Fxx and later as the picture...
