I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi there,
Is it at all possible to run nRF Connect for Desktop apps like the programmer and the power profiler from outside the nrf connect for desktop app?
e.g. is there...
Good day,
is there a way to check if a client is connected to GATT server/service? Would like to send a data after device gets reconnected.
i am using PCA10040 with...
Hello dear Nordic. I am wondering if I can simulate a hardware event by the software by writing any value to the event register, or in other words to create artificial interrupt...
Hi,
I implement the CLI on my nRF52820 and I see in function cursor_next_line_move in file nrf_cli.c they use "\n" but for my project I don't want to pass in cursor_next_line_move...
Hello,
I'm tryng to update nRF9160sip (rev b1), I push sw4 on power on and I see "MCUBOOT" device on "Programmer v3.03"
Then I select file "mfw_nrf9160_1.3.2.zip" and...
Hi,
I have made my own customboard with the nrf52811. For development I have used nrf52840dk.
I´m trying to program following:
I did solder one PCB by hand. It didn...
Hi Team,
I am looking for a new readily available to test on my Nordic board 52X version.
could you please share the inputs and the source code that i can test and upload...
Hello, is there a guide on what should be done to make the sample codes for the nrf52840_dk compatible with the nrf52840_dongle? If there isnt, can I please know how one can...
Hi,
we would like to set the USBD_SERIAL according to the device serial, which will be an abbreviated version of the MAC address. I've checked the code and can only find...
Hi,
I am getting a similar error. I have nRF52832 board connected to raspberry pi for flashing and debugging using openocd. As soon as openocd command is executed I start...
Hi guys. When reading the OOB pairing example,
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth/peripheral_nfc_pairing/README.html
" This...
Hope someone can bring some clarification to me.
I am studying the principle of Shock-burst and a part of that study is to go through every step in the examples of “esb_low_power_ptx_pca10056...
In My Window 10 PC., No connected devices are shown in VS Code when nRF52840 dongle is inserted in PC USB Port.
But in Programmer, nRF52840 dongle can be found.
Device...
Hardware:
Raspberry Pi Zero W
nRF52840 DK running Serial Example and connected to RPi via USB
Custom nRF52840 board acting as a Vendor Model Server
Software: ...
I'm trying to program an nRF52 on a custom PCB using the nRF52-DK and am getting an error when connecting with nRF Connect v3.6.1.
I made the following connections from...
