Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Our product consists of a Texas MSP430 and a Nordic nRF52832 Chip, with serial/UART between
for MSP programming, debug and development : I'm using the official TI MSP-FET...
I am testing programming secure bootloader. But J-Link Commander reports Could not start CPU core. (ErrorCode: -1) after programming softdevice, bootloader, and application...
Hi,
Now I'm going to use 52833 USB_CDC_ACM , but there is no suitable type in SDK17.1.0. It's just have pca10056 . So I port to 52833 based on the 52840_pca10056 routines...
Hi team,
I am using nRF52833 DK with PCA10100 on it.
I am developing app_timer application for blinking led for a fixed time interval. But it is not working properly....
Hello,
We are trying to adapt the simple_gw example to receive temperature measurements from a zigbee temperature sensor. However we do not succeed. We can find the device...
I'm using an nRF5340 DK board with ncs v2.0.0. I have to build an application that should access BLE running in the network core. I see there are two options provided, Remote...
Dear Nordic engineers
I have a probelm would like to ask you.
I read this link: https://infocenter.nordicsemi.com/index.jsp?topic=%2Ferrata_nRF21540_Rev2%2FERR%2FnRF21540...
Hello，
I am developing an AoA Tx project using NCS v1.9.0 & 52820. Some problems are hard to solve by myself.
Below is my configuration:
1.When CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC_CALIBRATION...
Hello,
we are using the "AT%CCLK?" at it works very nice.
but now for the challange... since the modem is synchronized with the LTE network and sends on the designated...
I notice a problem with the MCUboot Hello World example.
I followed the steps mentioned in https://www.mcuboot.com/documentation/readme-zephyr/ That is, build the MCUBoot...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v2.0.0 I could build with NCS v1.9.1 but I cannot build with NCS2.0
[Build log] In file included from C:/NCS200/v2.0.0/zephyr/include...
I have an Ellisys Bluetooth Explorer 400 sniffer and am trying to sniff the ISO audio data between nrf5340 ADK boards. I enabled CONFIG_BT_LOG_SNIFFER_INFO, CONFIG_BT_DEBUG_KEYS...
