Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hello, this is a follow up on this ticket: https://devzone.nordicsemi.com/f/nordic-q-a/84834/protecting-the-battery-via-sleep-mode
Our goal is to switch off the device ...
Hi,
I'm trying to understand which of the BT L2CAP modes are supported for a BT LE Controller. BT Core 5.3 supports these modes of operation:
Basic L2CAP Mode
Flow...
Hi.
Is it possible to add SPI or QSPI cleanup once mcuboot is done?
I've checked nrf_cleanup.c , but it seems that (Q)SPI is not turned off, which increases the power...
Hello,
I'm using nRF52833 MCU board for my project, I have to do power optimization to my project(Device).
In my device two sensors are there, and boost regulator and...
Hi, I have made a project that is based upon the aws_iot sample. The version of SDK and toolchain is 1.7.1. Now I have tried to upgrade to version 1.9.1. But then I get compile...
I've written a sample eeprom application based on the eeprom included in the nRF52 SDK to test the EEPROM we use in a project. The application worked properly about 10 days...
Hello! We created our own model using SDK for Mesh and it works well. However, when testing in the "nRF Mesh" application using the "Vendor Model Control" field with the ...
When i use GPIOTE HITOLO(low accuracy）and then open spi to read flash and close the SPI（nrf_drv_spi_uninit） and close the SPI 's GPIO (nrf_gpio_cfg_default) .
The power...
Hello,
How do I create an encrypted/signed image? Where can I find the documentation for doing this? How will I need to modify the bootloader to decode and install the image...
Hi, I need some help on flashing the code to nRF52832 BLE module. I would like to mention that I am flashing the code to nRF module using ST-link v2 debugger with the help...
Hi,
I've encountered problem with app timer functions being called from different interrupt levels. Looks like no memory error returned is caused by collision in underlaying...
Dear Nordic,
I'm trying to determine why my nRF9160 cannot register on the Verizon network. Does Nordic have any tools which allow one to see the RRC messages between the...
I just try to connect to J2 port like I always used. I tested several cables and several USB ports, I'm using MAC os. 1. Power switch is ON
2. nRF Power source switch is...
Hi ,
We are building a ble mesh related project with nrf52840 soc with NRF MESH SDK 5 . After certain amount of development work we are facing issues related to synchronization...
Hi Team,
I am using the solar beacon code from Nordic playground github for some reason and I know this is not qualified. I observe that the receiver suddenly misses a train...
