Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
I tried to create/ open a project using nRF Connect in SES. The error appears as shown in image. While the file exists as shown in the second image. Why, such error and what...
Hi,
Basically, the setup of the mesh network is as follows,
There are END NODES based on sensor server model.
There are RELAY NODES based on the sensor client model...
Hi,
I am using Zephyr3.0.0 to validate AOA CTE sampling.
Firstly, a s below is the official data format. Nordic Semiconductor Radio peripheral provides 16 bit wide IQ...
Hi,
I am able to successfully build and flash the Matter Light Bulb sample onto my nRF52840 DK.
I am now getting ready to configure the firmware for use on a custom board...
Hi,
NCS1.9.1,nRF5340DK, VSCode，
see code, timer_lms==1000 spend 1000ms
but if start i2s
i2s_audio_init(); //this line will Slow down the time
timer_lms==200 spend...
When i try to use SES to build my project.there is error.The enviroment i confige as descrblied. them i use toochainmanger in nrf connect tools,the error is as the same as...
I'm trying to determine how to get a Linux timestamp for a project using nRF9160. It looks like the mktime() function is not supported. Any suggestions?
thanks!
I'm running into a weird bug where the first 4 bits received by my SPIM are always 1 - the next 64.5 bytes are all correct though... I've built 3 FWs out of provided examples...
Hi guys,
I have developed an app to read data from some sensors and notify the central with a frequency of 100Hz. It seems to work but I would like to share my approach...
Hello,
We are trying to get UART communication between nRF9160 and MSP430.
MSP430 need to send out a sensor data through UART.
We are using 1.9.1 SDK, and Visual...
Hi,
Is it possible to remotely execute a command that would force a BLE node into indefinite sleep or standby mode?
I am working to build out a BLE mesh network, where...
Hi. We have a custom board featuring 4 FSR sensors on it, based on the Nrf52810. Initially i tested those boards and the sensors using an STLink-V2, along with the Arduino...
hi thanks for you heip!
i want use \nRF5_SDK_17.1.0_ddde560\examples\peripheral\radio_test for radio test, here is the questions:
1、could this example can send prbs9 wave...
Hello!
I have to decode signals from two quadrature encoders. I know nordic has a driver for this, QDEC, however. there are a couple problems:
1. I need to control two...
