Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
I have attached all sleep modes of our controller that i found through forums and from your suggestions.
But my problem is No one of these sleep modes, wake-up through...
Hi,
I am just starting out creating a project to run on an nRF9160 on custom hardware. I have set up a development environment (v1.9.0) through nRF Connect for Desktop...
Hello I use nrf52840 and BME280. I plugged it GND GND SDA 45 (P1.13) SCL 47 (P1.15) VCC 32 (P1.00) I use timer to refresh data and on the first line of the code I init gpio...
Hi,
In the nRF52840 Product Specification 1.7 , page 34 chapter 4.4.1.9 INFO.VARIANT, I read that the hex code of variant "AAF0" is 0x4141 45 30. However the description...
Configuration :
IDE : SES V5.70a
SDK version : NRF5_SDK_17.1.0
Board : NRF52840DK
Hello,
I'd like to use 4 channels of the ADC in a scan mode at a high frequency...
Hi,
I am working on an application to transfer firmware file via BLE-GATT to nRF52833. Can you kindly suggest any sample code for me to evaluate.
Thanks,
Ubaid
Hi,
I've been following this tutorial regarding connecting my BLE device to another Bluetooth module:
https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/getting...
Hello,
I have a question regarding NRFX_SPIS_XFER_DONE event. Documentation says that this means "SPI transaction has been completed."
I'm curious if this event is triggered...
Hi,
I have just bumped the NCS I am using for my project to version 1.9.1. After this update, I found a bug in the Zephyr code.
On line 214 of zephyr/subsys/net/lib/lwm2m...
After some advice here, Typically I use the native or recommended IDE's for the platform I'm working with and generally have no issues getting up and running. This time around...
Hi,
I am using NCS v1.9.0 and have a question about datatime module.
It seems to have NTP and Modem clock sources, but I don't want to use either clock source. I have...
Hi
Thank you for your attention to my question, I would like to inquire how to control each channel of hardware PWM individually, We have 6 LED lights, each LED has different...
Hi, I am running Sample DFU app based on peripheral_lbs suggested by nordic on BL653dvk : https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs...
is it possible to transfer my emulated code from the nRF52840 to the nRF 52811? How do i do that? Or a better question; how do i write my code on the nrf52811 using the nRF52840...
I am working from this video:
https://webinars.nordicsemi.com/developing-bluetooth-low-energy-6
Which nRF5340-DK build configuration should I use please?
nrff5340dk_nrf5340_cpuapp...
