I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi,
I'm using the nRF Connect for VS Code with SDK version 1.8.0.
Working with one custom PCB with nRF52840 as the peripheral and another custom PCB with nRF52840 as the...
Hi we are in the preproduction phase and we see that in the market there are two order codes NRF9160-SICA-B1A-R and NRF9160-SICA-R.
Looking at the datasheet it looks like...
Hi there,
I am trying to obtain a .hex file for my project for Release Configuration. I don't see the .hex file get updated in the pca10040\s132\ses\Output\Release\Exe directory...
I am a electrical engineering student in my final year of study and am developing a product for my final year dissertation.
The project idea is to help identify sickness...
Hello,
I am using,
iPhone 7
iOS v14.8.1
nRF Connect for Mobile iOS v2.4.13
I have used nRF Connect for Mobile on android which shows this menu when peripheral...
I am using the NRF52840-DK and using the Zigbee light bulb example.
1. The DK board successfully connects to the zigbee network - Z2M in this case.
2. I have added an...
Hi everyone, my colleague developed a firmware using Arduino Nano 33 BLE and PlatformIO. Now I have to rewrite the code using Segger Embedded Studio. The problem is in the...
Hi there, I am developing a peripheral to central system with nrf52840 base on NUS service. Now I tried to increase the MTU of the peripheral to 247 to increase the transfer...
Hi,
I am using NCS for development and configuring GPIO pin as input, but I found the GPIO can't configuring as NO-PULL mode. There are only two options: Pull up and Pull...
Hi,
I am working on ble_bms_app template. While the nrf52840dk is connected to laptop, I don't get JLINK connected notification on the desktop. Sometimes i get the connected...
Hello.
I'm using nrf52832 (S132 v7.0.1, SDK v17.0.0) to develop peripheral roles.
Setting UUIDs for advertisements, services, and characteristics. At that time, sd_ble_uuid_vs_add...
Hello.
I am developing using nrf52832 (S132 v7.0.1, SDK v16.0.0) as central and Android device (Bluetooth 4.2) as advertise. Android devices use nRF Connect.
I can set...
We are aiming at a low pin count interface between modules. Ideally we would like to use the programming pins for both programming and as an I2C interface. Is this possible...
