Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
I need to send data over ModBus-RTU (basically RS485) from an nRF52840. For this, I use uarte. The transceiver's transmit enable input is controlled through a GPIO pin, which...
1. I've deleted the peers from the device by running the BMS sdk example, still i am unable to connect the previously bonded device where i"ve deleted the key.
2. The pm_evt_handler...
I get NRF_ERROR_FORBIDDEN error when I want to send a software message to the server device in the Light_switch application, except for the button. But when I press the button...
Hello,
I used exampl:
nRF5_SDK_17.0.2_d674dde/examples/ble_peripheral/ble_app_hids_keyboard
Why can't I see any HID Services in apps (nrf Connect) in iphone 12?
But...
Hi, I've read that when NFCT is operative the internal resistor of SoC is automatically adjusted. For antenna tuning this resistance can be set to a fixed value through a...
Hi there,
My current setup:
1. Custom board.
2. SDK nRF5 SDK v17.0.2
3. Application running BLE (SoftDevice)
Using the USB CDC Class example to be able to interface...
I'm using nRF51 sniffer to capture BLE packets for group of devices. Sniffer can able to capture only primary advertisement channels and not secondary advertisement channels...
Dear Members,
I want to use this code :
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk51.v10.0.0%2Fant_examples_bpwr.html
Does it work...
Excuse me:
As shown in the figure below, can this type of crystal oscillator be used on nrf52832? How to connect this crystal oscillator with XC1 and XC2 of nrf52832?
Hi,
we are preparing for certification and are about to test with the DTM v1.0. now in nAN43 it states following:
1.1.1 Hardware requirements • nRF8001 Development Kit...
I try to add pairing/bonding to the NCS hello world project. But I found the information is not easy to find. I'm playing with the bt_conn_auth_cb struct to understand how...
Hello,
I am trying to verify a signature with the `NIST p-256` curve. I had previously done this with the Nrf5 sdk and it is working:
I am now trying to migrate...
Hello Nordic Team,
as a newbie in the Nordic world, I have been reading the nRF Connect SDK and Zephyr documentation as well as testing some of the samples on my nRF5340DK...
