According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi,
I have got some problem of understanding the IQ sampling data.
As below is the official data format
0: I_Q (default)
Q
31:16
12 bits signed, sign extended...
I have successfully installed the drivers and downloaded the latest firmware version, but the connexion fails and I can not use the AT interfaces command for the modem controller...
Hi
I am using an example project written for pca_10040, I am trying to replace it with pca_10010.
So far, I changed the "Target Device" in the project options and the...
Hi all,
Currently we are trying to measure the power of nRF52832 using (1) nRF52 DK board, (2) power profiler kit 2 (PPK2).
We used PPK2 in source-meter mode and we connected...
Shalom!
I have a custom nRF9160 board with uart0 connected to the outside world by RS232. I set the uart0 as the printk() debug output. I also need to write and read binary...
I get that is has to do with something around the MSB. But I cant seem to find a way to prevent this. No i can not send a byte 0x00 since this will trigger certaint behavior...
Hi,
I am developing an Openthread application using Nordic Connect SDK for the nrf52840dongle. I updated my nrf SDK to bd075cc09. Since then, my application won't boot anymore...
Hi,
I need to switch DK to 3v as my custom board has 3v.
When I switch VDD_IO to 3v board doesn't start at all. LED5 blinks for a moment but nothing happens.
Switching...
Hi,
I am currently working on an internal dfu modeled after the secure_bootloader_uart/ example in SDK 15.3.0. I have gotten the dfu to perform a successful dfu with the...
Hi!
I am developing on a custom board and only have the Debug in connector P3 from nrf9160dk to debug the board. I want to send AT commands to configure the modem and will...
I am a systems engineer helping my team in the component selection phase of the project that involves BLE communication between our master side and a simple remote control...
I have issue to program nrf52832 with nrfjprog command line.
my program use nrf52formesh sdk. I developed with Segger Embedded Studio with GCC on the Linux PC. I modified...
Hello all,
I have successfully installed nRF Connect, nRF Connect SDK v1.6.0 and SEGGER Embedded Studio (SES) v5.50.c to run and debug some samples on my nRF5340 Development...
Hello everyone,
I CAN NOT include the ocrypto_ecdsa_p256_public_key.h file into my project.
What are configurations I need to enable?
I'm new to NCS, could you provide...
