I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
I want to connect an external led to the nrf5340 pdk to perform the same function as the blinky example.
I connected this led to D0 (PIN P1.00), but I don't know...
Hi,
We are trying to send a mesh packets containing 72 bytes from client to server with reliable message transmission method (Using access_model_reliable_cancel() based...
nRF52840 with SoftDevice s140, rev 7.01. For this errata, the work around is to use READY instead. Is the SoftDevice doing this? I can't find any info. I did find a related...
We're using the nRF52840 along with SoftDevice s140 version 7.01 for a medical device. Reviewing the nRF52840 Errata sheet, Rev2, there is an errata "242 NVMC: NVMC operations...
Hi nordic community,
I'm using Open Thread Border Router build using Linux and an nrf52840 dk board, I want to show my sensor data in open thread border router web GUI,...
Hello,
I have changed the provided UDP sample to send some cellular data (RSRP, RSRQ) to our server within an fixed intervall. So I am using a few AT commands (at_cmd_write...
Hi, like the title says I am having trouble implementing the MQTT Publisher example found in the nRF5 SDK for Thread and Zigbee v4.1.0 . I'm using a Raspberry Pi 4 with the...
Have a medical device in production using nRF52840 with SoftDevice s140, 7.01. Is this Errata fixed or a workaround is implemented in this SoftDevice version or any version...
Hi Nordic Team:
1. I use this example " Thread MQTT-SN Example ".
after i compile the code than i do the step below
1.Build the example according to the instructions...
Hello,
What are all the supported cipher suites for the nrf9160? Per your documentation, it seems AES 128 is supported but not AES 256. But, based on some testing with slightly...
What is the thermal resistance for the following part number: nRF52832-QFAA-R
specifically the thermal resistance between the junction and the ambient in C/W
Dear Nordic,
we are developing DFU Secure bootloader for a nRF52832 based HW.
We are starting from the "\examples\dfu\secure_bootloader" . First of all, we succesfully...
Hi,
Actually in my program I have a serial uart interface that cause an interrupt when a message is receive. During the interrupt, I send a mesh model command and its works...
Here I use gpiote and Ble_template_example.
The advertisement code is working fine but now I use button interrupt to send different payload or the button press change...
My understanding is that secure boot calls an interface to make portion flash that contains a bootloader immutable. Since this is called after the bootloader start to run...
